feat(core): change rover_platform parameter to override, default with hostname instead of environment variable

Launch file uses clucky, testbed, auto. Node was using core, testbed, auto. Replaced core with clucky in the node.

README.md

@@ -60,6 +60,33 @@ $ ros2 launch anchor_pkg rover.launch.py  # Must be run on a computer connected
 $ ros2 run headless_pkg headless_full  # Optionally run in a separate shell on the same or different computer.
 ```
 
+### Using the Mock Connector
+
+Anchor provides a mock connector meant for testing and scripting purposes. You can select the mock connector by running anchor with this command:
+
+```bash
+$ ros2 launch anchor_pkg rover.launch.py connector:="mock"
+```
+
+To see all data that would be sent over the CAN network (and thus to the microcontrollers), use this command:
+
+```bash
+$ ros2 topic echo /anchor/to_vic/debug
+```
+
+To send data to the mock connector (as if you were a ROS2 node), use the normal relay topic:
+
+```bash
+$ ros2 topic pub /anchor/to_vic/relay astra_msgs/msg/VicCAN '{mcu_name: "core", command_id: 50, data: [0.0, 2.0, 0.0, 1.0]}'
+
+```
+
+To send data to the mock connector (as if you were a microcontroller), publish to the dedicated topic:
+
+```bash
+$ ros2 topic pub /anchor/from_vic/mock_mcu astra_msgs/msg/VicCAN '{mcu_name: "arm", command_id: 55, data: [0.0, 450.0, 900.0, 0.0]}'
+```
+
 ### Testing Serial
 
 You can fake the presence of a Serial device (i.e., MCU) by using the following command:
@@ -68,10 +95,31 @@ You can fake the presence of a Serial device (i.e., MCU) by using the following
 $ socat -dd -v pty,rawer,crnl,link=/tmp/ttyACM9 pty,rawer,crnl,link=/tmp/ttyOUT
 ```
 
-When you go to run anchor, use the `PORT_OVERRIDE` environment variable to point it to the fake serial port, like so:
+When you go to run anchor, use the `serial_override` ROS2 parameter to point it to the fake serial port, like so:
 
 ```bash
-$ PORT_OVERRIDE=/tmp/ttyACM9 ros2 launch anchor_pkg rover.launch.py
+$ ros2 launch anchor_pkg rover.launch.py connector:=serial serial_override:=/tmp/ttyACM9
+```
+
+### Testing CAN
+
+You can create a virtual CAN network by using the following commands to create and then enable it:
+
+```bash
+sudo ip link add dev vcan0 type vcan
+sudo ip link set vcan0 up
+```
+
+When you go to run anchor, use the `can_override` ROS2 parameter to point it to the virtual CAN network, like so:
+
+```bash
+$ ros2 launch anchor_pkg rover.launch.py connector:=can can_override:=vcan0
+```
+
+Once you're done, you should delete the virtual network so that anchor doesn't get confused if you plug in a real CAN adapter:
+
+```bash
+$ sudo ip link delete vcan0
 ```
 
 ### Connecting the GuliKit Controller

flake.lock

@@ -60,7 +60,8 @@
         "nixpkgs": [
           "nix-ros-overlay",
           "nixpkgs"
-        ]
+        ],
+        "treefmt-nix": "treefmt-nix"
       }
     },
     "systems": {
@@ -77,6 +78,26 @@
         "repo": "default",
         "type": "github"
       }
+    },
+    "treefmt-nix": {
+      "inputs": {
+        "nixpkgs": [
+          "nixpkgs"
+        ]
+      },
+      "locked": {
+        "lastModified": 1773297127,
+        "narHash": "sha256-6E/yhXP7Oy/NbXtf1ktzmU8SdVqJQ09HC/48ebEGBpk=",
+        "owner": "numtide",
+        "repo": "treefmt-nix",
+        "rev": "71b125cd05fbfd78cab3e070b73544abe24c5016",
+        "type": "github"
+      },
+      "original": {
+        "owner": "numtide",
+        "repo": "treefmt-nix",
+        "type": "github"
+      }
     }
   },
   "root": "root",

flake.nix

@@ -4,6 +4,11 @@
   inputs = {
     nix-ros-overlay.url = "github:lopsided98/nix-ros-overlay/develop";
     nixpkgs.follows = "nix-ros-overlay/nixpkgs"; # IMPORTANT!!!
+
+    treefmt-nix = {
+      url = "github:numtide/treefmt-nix";
+      inputs.nixpkgs.follows = "nixpkgs";
+    };
   };
 
   outputs =
@@ -11,7 +16,8 @@
       self,
       nix-ros-overlay,
       nixpkgs,
-    }:
+      ...
+    }@inputs:
     nix-ros-overlay.inputs.flake-utils.lib.eachDefaultSystem (
       system:
       let
@@ -28,6 +34,7 @@
             (python313.withPackages (
               p: with p; [
                 pyserial
+                python-can
                 pygame
                 scipy
                 crccheck
@@ -83,6 +90,8 @@
             export QT_X11_NO_MITSHM=1
           '';
         };
+
+        formatter = (inputs.treefmt-nix.lib.evalModule pkgs ./treefmt.nix).config.build.wrapper;
       }
     );
 

src/anchor_pkg/anchor_pkg/anchor_node.py

@@ -1,28 +1,24 @@
+from warnings import deprecated
 import rclpy
 from rclpy.node import Node
 from rclpy.executors import ExternalShutdownException
-from std_srvs.srv import Empty
+from rcl_interfaces.msg import ParameterDescriptor, ParameterType
 
-import signal
-import time
 import atexit
 
-import serial
+from .connector import (
-import serial.tools.list_ports
+    Connector,
-import os
+    MockConnector,
-import sys
+    SerialConnector,
+    CANConnector,
+    NoValidDeviceException,
+    NoWorkingDeviceException,
+)
+from .convert import string_to_viccan
 import threading
-import glob
 
-from std_msgs.msg import String, Header
 from astra_msgs.msg import VicCAN
-
+from std_msgs.msg import String
-KNOWN_USBS = [
-    (0x2E8A, 0x00C0),  # Raspberry Pi Pico
-    (0x1A86, 0x55D4),  # Adafruit Feather ESP32 V2
-    (0x10C4, 0xEA60),  # DOIT ESP32 Devkit V1
-    (0x1A86, 0x55D3),  # ESP32 S3 Development Board
-]
 
 
 class Anchor(Node):
@@ -36,308 +32,204 @@ class Anchor(Node):
         - VicCAN messages for Arm node
     * /anchor/from_vic/bio
         - VicCAN messages for Bio node
+    * /anchor/to_vic/debug
+        - A string copy of the messages published to ./relay are published here
 
     Subscribers:
     * /anchor/from_vic/mock_mcu
-        - For testing without an actual MCU, publish strings here as if they came from an MCU
+        - For testing without an actual MCU, publish ViCAN messages here as if they came from an MCU
     * /anchor/to_vic/relay
         - Core, Arm, and Bio publish VicCAN messages to this topic to send to the MCU
     * /anchor/to_vic/relay_string
-        - Publish raw strings to this topic to send directly to the MCU for debugging
+        - Send raw strings to connectors. Does not work for connectors that require conversion (like CANConnector)
+    * /anchor/relay
+        - Legacy method for talking to connectors. Takes String as input, but does not send the raw strings to connectors.
+          Instead, it converts them to VicCAN messages first.
     """
 
+    connector: Connector
+
     def __init__(self):
-        # Initalize node with name
+        super().__init__("anchor_node")
-        super().__init__("anchor_node")  # previously 'serial_publisher'
 
-        self.serial_port: str | None = None  # e.g., "/dev/ttyUSB0"
+        logger = self.get_logger()
 
-        # Serial port override
+        # ROS2 Parameter Setup
-        if port_override := os.getenv("PORT_OVERRIDE"):
-            self.serial_port = port_override
 
-        ##################################################
+        self.declare_parameter(
-        # Serial MCU Discovery
+            "connector",
-
+            "auto",
-        # If there was not a port override, look for a MCU over USB for Serial.
+            ParameterDescriptor(
-        if self.serial_port is None:
+                name="connector",
-            comports = serial.tools.list_ports.comports()
+                description="Declares which MCU connector should be used. Defaults to 'auto'.",
-            real_ports = list(
+                type=ParameterType.PARAMETER_STRING,
-                filter(
+                additional_constraints="Must be 'serial', 'can', 'mock', or 'auto'.",
-                    lambda p: p.vid is not None
+            ),
-                    and p.pid is not None
-                    and p.device is not None,
-                    comports,
         )
-            )
-            recog_ports = list(filter(lambda p: (p.vid, p.pid) in KNOWN_USBS, comports))
 
-            if len(recog_ports) == 1:  # Found singular recognized MCU
+        self.declare_parameter(
-                found_port = recog_ports[0]
+            "can_override",
-                self.get_logger().info(
+            "",
-                    f"Selecting MCU '{found_port.description}' at {found_port.device}."
+            ParameterDescriptor(
+                name="can_override",
+                description="Overrides which CAN channel will be used. Defaults to ''.",
+                type=ParameterType.PARAMETER_STRING,
+                additional_constraints="Must be a valid CAN network that shows up in `ip link show`.",
+            ),
         )
-                self.serial_port = found_port.device  # String, location of device file; e.g., '/dev/ttyACM0'
-            elif len(recog_ports) > 1:  # Found multiple recognized MCUs
-                # Kinda jank log message
-                self.get_logger().error(
-                    f"Found multiple recognized MCUs: {[p.device for p in recog_ports].__str__()}"
-                )
-                # Don't set self.serial_port; later if-statement will exit()
-            elif (
-                len(recog_ports) == 0 and len(real_ports) > 0
-            ):  # Found real ports but none recognized; i.e. maybe found an IMU or camera but not a MCU
-                self.get_logger().error(
-                    f"No recognized MCUs found; instead found {[p.device for p in real_ports].__str__()}."
-                )
-                # Don't set self.serial_port; later if-statement will exit()
-            else:  # Found jack shit
-                self.get_logger().error("No valid Serial ports specified or found.")
-                # Don't set self.serial_port; later if-statement will exit()
 
-        # We still don't have a serial port; fall back to legacy discovery (Areeb's code)
+        self.declare_parameter(
-        # Loop through all serial devices on the computer to check for the MCU
+            "serial_override",
-        if self.serial_port is None:
+            "",
-            self.get_logger().warning("Falling back to legacy MCU discovery...")
+            ParameterDescriptor(
-            ports = Anchor.list_serial_ports()
+                name="serial_override",
-            for _ in range(4):
+                description="Overrides which serial port will be used. Defaults to ''.",
-                if self.serial_port is not None:
+                type=ParameterType.PARAMETER_STRING,
-                    break
+                additional_constraints="Must be a valid path to a serial device file that shows up in `ls /dev/tty*`.",
-                for port in ports:
+            ),
+        )
+
+        # Determine which connector to use. Options are Mock, Serial, and CAN
+        connector_select = (
+            self.get_parameter("connector").get_parameter_value().string_value
+        )
+        can_override = (
+            self.get_parameter("can_override").get_parameter_value().string_value
+        )
+        serial_override = (
+            self.get_parameter("serial_override").get_parameter_value().string_value
+        )
+        match connector_select:
+            case "serial":
+                logger.info("using serial connector")
+                self.connector = SerialConnector(
+                    logger, self.get_clock(), serial_override
+                )
+            case "can":
+                logger.info("using CAN connector")
+                self.connector = CANConnector(logger, self.get_clock(), can_override)
+            case "mock":
+                logger.info("using mock connector")
+                self.connector = MockConnector(logger, self.get_clock())
+            case "auto":
+                logger.info("automatically determining connector")
                 try:
-                        # connect and send a ping command
+                    logger.info("trying CAN connector")
-                        ser = serial.Serial(port, 115200, timeout=1)
+                    self.connector = CANConnector(
-                        # (f"Checking port {port}...")
+                        logger, self.get_clock(), can_override
-                        ser.write(b"ping\n")
-                        response = ser.read_until(bytes("\n", "utf8"))
-
-                        # if pong is in response, then we are talking with the MCU
-                        if b"pong" in response:
-                            self.serial_port = port
-                            self.get_logger().info(f"Found MCU at {self.serial_port}!")
-                            break
-                    except:
-                        pass
-
-        # If port is still None then we ain't finding no mcu
-        if self.serial_port is None:
-            self.get_logger().error("Unable to find MCU. Exiting...")
-            time.sleep(1)
-            sys.exit(1)
-        # Found a Serial port, try to open it; above code has not officially opened a Serial port
-        else:
-            self.get_logger().debug(
-                f"Attempting to open Serial port '{self.serial_port}'..."
                     )
-            try:
+                except (NoValidDeviceException, NoWorkingDeviceException, TypeError):
-                self.serial_interface = serial.Serial(
+                    logger.info("CAN connector failed, trying serial connector")
-                    self.serial_port, 115200, timeout=1
+                    self.connector = SerialConnector(
+                        logger, self.get_clock(), serial_override
                     )
-
+            case _:
-                # Attempt to get name of connected MCU
+                logger.fatal(
-                self.serial_interface.write(
+                    f"invalid value for connector parameter: {connector_select}"
-                    b"can_relay_mode,on\n"
-                )  # can_relay_ready,[mcu]
-                mcu_name: str = ""
-                for _ in range(4):
-                    response = self.serial_interface.read_until(bytes("\n", "utf8"))
-                    try:
-                        if b"can_relay_ready" in response:
-                            args: list[str] = response.decode("utf8").strip().split(",")
-                            if len(args) == 2:
-                                mcu_name = args[1]
-                            break
-                    except UnicodeDecodeError:
-                        pass  # ignore malformed responses
-                self.get_logger().info(
-                    f"MCU '{mcu_name}' is ready at '{self.serial_port}'."
                 )
+                exit(1)
 
-            except serial.SerialException as e:
-                self.get_logger().error(
-                    f"Could not open Serial port '{self.serial_port}' for reason:"
-                )
-                self.get_logger().error(e.strerror)
-                time.sleep(1)
-                sys.exit(1)
-
-        # Close serial port on exit
-        atexit.register(self.cleanup)
-
-        ##################################################
         # ROS2 Topic Setup
 
-        # New pub/sub with VicCAN
+        # Publishers
-        self.fromvic_debug_pub_ = self.create_publisher(
+        self.fromvic_debug_pub_ = self.create_publisher(  # only used by serial
-            String, "/anchor/from_vic/debug", 20
+            String,
+            "/anchor/from_vic/debug",
+            20,
         )
         self.fromvic_core_pub_ = self.create_publisher(
-            VicCAN, "/anchor/from_vic/core", 20
+            VicCAN,
+            "/anchor/from_vic/core",
+            20,
         )
         self.fromvic_arm_pub_ = self.create_publisher(
-            VicCAN, "/anchor/from_vic/arm", 20
+            VicCAN,
+            "/anchor/from_vic/arm",
+            20,
         )
         self.fromvic_bio_pub_ = self.create_publisher(
-            VicCAN, "/anchor/from_vic/bio", 20
+            VicCAN,
+            "/anchor/from_vic/bio",
+            20,
+        )
+        # Debug publisher
+        self.tovic_debug_pub_ = self.create_publisher(
+            VicCAN,
+            "/anchor/to_vic/debug",
+            20,
         )
 
-        self.mock_mcu_sub_ = self.create_subscription(
+        # Subscribers
-            String, "/anchor/from_vic/mock_mcu", self.on_mock_fromvic, 20
-        )
         self.tovic_sub_ = self.create_subscription(
-            VicCAN, "/anchor/to_vic/relay", self.on_relay_tovic_viccan, 20
+            VicCAN,
+            "/anchor/to_vic/relay",
+            self.write_connector,
+            20,
         )
-        self.tovic_debug_sub_ = self.create_subscription(
+        self.tovic_sub_legacy_ = self.create_subscription(
-            String, "/anchor/to_vic/relay_string", self.on_relay_tovic_string, 20
+            String,
+            "/anchor/relay",
+            self.write_connector_legacy,
+            20,
+        )
+        self.mock_mcu_sub_ = self.create_subscription(
+            String,
+            "/anchor/from_vic/mock_mcu",
+            self.relay_fromvic,
+            20,
+        )
+        self.tovic_string_sub_ = self.create_subscription(
+            String,
+            "/anchor/to_vic/relay_string",
+            self.connector.write_raw,
+            20,
         )
 
-        # Create publishers
+        # Close devices on exit
-        self.arm_pub = self.create_publisher(String, "/anchor/arm/feedback", 10)
+        atexit.register(self.cleanup)
-        self.core_pub = self.create_publisher(String, "/anchor/core/feedback", 10)
-        self.bio_pub = self.create_publisher(String, "/anchor/bio/feedback", 10)
-
-        self.debug_pub = self.create_publisher(String, "/anchor/debug", 10)
-
-        # Create a subscriber
-        self.relay_sub = self.create_subscription(
-            String, "/anchor/relay", self.on_relay_tovic_string, 10
-        )
-
-    def read_MCU(self):
-        """Check the USB serial port for new data from the MCU, and publish string to appropriate topics"""
-        try:
-            output = str(self.serial_interface.readline(), "utf8")
-
-            if output:
-                self.relay_fromvic(output)
-                # All output over debug temporarily
-                # self.get_logger().info(f"[MCU] {output}")
-                msg = String()
-                msg.data = output
-                self.debug_pub.publish(msg)
-                if output.startswith("can_relay_fromvic,core"):
-                    self.core_pub.publish(msg)
-                elif output.startswith("can_relay_fromvic,arm") or output.startswith(
-                    "can_relay_fromvic,digit"
-                ):  # digit for voltage readings
-                    self.arm_pub.publish(msg)
-                if output.startswith("can_relay_fromvic,citadel") or output.startswith(
-                    "can_relay_fromvic,digit"
-                ):  # digit for SHT sensor
-                    self.bio_pub.publish(msg)
-                # msg = String()
-                # msg.data = output
-                # self.debug_pub.publish(msg)
-                return
-        except serial.SerialException as e:
-            print(f"SerialException: {e}")
-            print("Closing serial port.")
-            try:
-                if self.serial_interface.is_open:
-                    self.serial_interface.close()
-            except:
-                pass
-            exit(1)
-        except TypeError as e:
-            print(f"TypeError: {e}")
-            print("Closing serial port.")
-            try:
-                if self.serial_interface.is_open:
-                    self.serial_interface.close()
-            except:
-                pass
-            exit(1)
-        except Exception as e:
-            print(f"Exception: {e}")
-            # print("Closing serial port.")
-            # if self.ser.is_open:
-            #     self.ser.close()
-            # exit(1)
-
-    def on_mock_fromvic(self, msg: String):
-        """For testing without an actual MCU, publish strings here as if they came from an MCU"""
-        # self.get_logger().info(f"Got command from mock MCU: {msg}")
-        self.relay_fromvic(msg.data)
-
-    def on_relay_tovic_viccan(self, msg: VicCAN):
-        """Relay a VicCAN message to the MCU"""
-        output: str = f"can_relay_tovic,{msg.mcu_name},{msg.command_id}"
-        for num in msg.data:
-            output += f",{round(num, 7)}"  # limit to 7 decimal places
-        output += "\n"
-        # self.get_logger().info(f"VicCAN relay to MCU: {output}")
-        self.serial_interface.write(bytes(output, "utf8"))
-
-    def relay_fromvic(self, msg: str):
-        """Relay a string message from the MCU to the appropriate VicCAN topic"""
-        self.fromvic_debug_pub_.publish(String(data=msg))
-        parts = msg.strip().split(",")
-        if len(parts) > 0 and parts[0] != "can_relay_fromvic":
-            self.get_logger().debug(f"Ignoring non-VicCAN message: '{msg.strip()}'")
-            return
-
-        # String validation
-        malformed: bool = False
-        malformed_reason: str = ""
-        if len(parts) < 3 or len(parts) > 7:
-            malformed = True
-            malformed_reason = (
-                f"invalid argument count (expected [3,7], got {len(parts)})"
-            )
-        elif parts[1] not in ["core", "arm", "digit", "citadel", "broadcast"]:
-            malformed = True
-            malformed_reason = f"invalid mcu_name '{parts[1]}'"
-        elif not (parts[2].isnumeric()) or int(parts[2]) < 0:
-            malformed = True
-            malformed_reason = f"command_id '{parts[2]}' is not a non-negative integer"
-        else:
-            for x in parts[3:]:
-                try:
-                    float(x)
-                except ValueError:
-                    malformed = True
-                    malformed_reason = f"data '{x}' is not a float"
-                    break
-
-        if malformed:
-            self.get_logger().warning(
-                f"Ignoring malformed from_vic message: '{msg.strip()}'; reason: {malformed_reason}"
-            )
-            return
-
-        # Have valid VicCAN message
-
-        output = VicCAN()
-        output.mcu_name = parts[1]
-        output.command_id = int(parts[2])
-        if len(parts) > 3:
-            output.data = [float(x) for x in parts[3:]]
-        output.header = Header(
-            stamp=self.get_clock().now().to_msg(), frame_id="from_vic"
-        )
-
-        # self.get_logger().info(f"Relaying from MCU: {output}")
-        if output.mcu_name == "core":
-            self.fromvic_core_pub_.publish(output)
-        elif output.mcu_name == "arm" or output.mcu_name == "digit":
-            self.fromvic_arm_pub_.publish(output)
-        elif output.mcu_name == "citadel" or output.mcu_name == "digit":
-            self.fromvic_bio_pub_.publish(output)
-
-    def on_relay_tovic_string(self, msg: String):
-        """Relay a raw string message to the MCU for debugging"""
-        message = msg.data
-        # self.get_logger().info(f"Sending command to MCU: {msg}")
-        self.serial_interface.write(bytes(message, "utf8"))
-
-    @staticmethod
-    def list_serial_ports():
-        return glob.glob("/dev/ttyUSB*") + glob.glob("/dev/ttyACM*")
 
     def cleanup(self):
-        print("Cleaning up before terminating...")
+        self.connector.cleanup()
-        if self.serial_interface.is_open:
+
-            self.serial_interface.close()
+    def read_connector(self):
+        """Check the connector for new data from the MCU, and publish string to appropriate topics"""
+        viccan, raw = self.connector.read()
+
+        if raw:
+            self.fromvic_debug_pub_.publish(String(data=raw))
+
+        if viccan:
+            self.relay_fromvic(viccan)
+
+    def write_connector(self, msg: VicCAN):
+        """Write to the connector and send a copy to /anchor/to_vic/debug"""
+        self.connector.write(msg)
+        self.tovic_debug_pub_.publish(msg)
+
+    @deprecated(
+        "Use /anchor/to_vic/relay or /anchor/to_vic/relay_string instead of /anchor/relay"
+    )
+    def write_connector_legacy(self, msg: String):
+        """Write to the connector by first attempting to convert String to VicCAN"""
+        # please do not reference this code. ~riley
+        for cmd in msg.data.split("\n"):
+            viccan = string_to_viccan(
+                cmd,
+                "anchor",
+                self.get_logger(),
+                self.get_clock().now().to_msg(),
+            )
+            if viccan:
+                self.write_connector(viccan)
+
+    def relay_fromvic(self, msg: VicCAN):
+        """Relay a message from the MCU to the appropriate VicCAN topic"""
+        if msg.mcu_name == "core":
+            self.fromvic_core_pub_.publish(msg)
+        elif msg.mcu_name == "arm" or msg.mcu_name == "digit":
+            self.fromvic_arm_pub_.publish(msg)
+        elif msg.mcu_name == "citadel" or msg.mcu_name == "digit":
+            self.fromvic_bio_pub_.publish(msg)
 
 
 def main(args=None):
@@ -350,16 +242,9 @@ def main(args=None):
 
         rate = anchor_node.create_rate(100)  # 100 Hz -- arbitrary rate
         while rclpy.ok():
-            anchor_node.read_MCU()  # Check the MCU for updates
+            anchor_node.read_connector()  # Check the connector for updates
             rate.sleep()
     except (KeyboardInterrupt, ExternalShutdownException):
         print("Caught shutdown signal, shutting down...")
     finally:
         rclpy.try_shutdown()
-
-
-if __name__ == "__main__":
-    signal.signal(
-        signal.SIGTERM, lambda signum, frame: sys.exit(0)
-    )  # Catch termination signals and exit cleanly
-    main()

src/anchor_pkg/anchor_pkg/connector.py

@@ -0,0 +1,438 @@
+from abc import ABC, abstractmethod
+from astra_msgs.msg import VicCAN
+from rclpy.clock import Clock
+from rclpy.impl.rcutils_logger import RcutilsLogger
+from .convert import string_to_viccan as _string_to_viccan, viccan_to_string
+
+# CAN
+import can
+import can.interfaces.socketcan
+import struct
+
+# Serial
+import serial
+import serial.tools.list_ports
+
+KNOWN_USBS = [
+    (0x2E8A, 0x00C0),  # Raspberry Pi Pico
+    (0x1A86, 0x55D4),  # Adafruit Feather ESP32 V2
+    (0x10C4, 0xEA60),  # DOIT ESP32 Devkit V1
+    (0x1A86, 0x55D3),  # ESP32 S3 Development Board
+]
+BAUD_RATE = 115200
+
+MCU_IDS = [
+    "broadcast",
+    "core",
+    "arm",
+    "digit",
+    "faerie",
+    "citadel",
+    "libs",
+]
+
+
+class NoValidDeviceException(Exception):
+    pass
+
+
+class NoWorkingDeviceException(Exception):
+    pass
+
+
+class MultipleValidDevicesException(Exception):
+    pass
+
+
+class DeviceClosedException(Exception):
+    pass
+
+
+class Connector(ABC):
+    logger: RcutilsLogger
+    clock: Clock
+
+    def string_to_viccan(self, msg: str, mcu_name: str):
+        """function currying so that we do not need to pass logger and clock every time"""
+        return _string_to_viccan(
+            msg,
+            mcu_name,
+            self.logger,
+            self.clock.now().to_msg(),
+        )
+
+    def __init__(self, logger: RcutilsLogger, clock: Clock):
+        self.logger = logger
+        self.clock = clock
+
+    @abstractmethod
+    def read(self) -> tuple[VicCAN | None, str | None]:
+        """
+        Must return a tuple of (VicCAN, debug message or string repr of VicCAN)
+        """
+        pass
+
+    @abstractmethod
+    def write(self, msg: VicCAN):
+        pass
+
+    @abstractmethod
+    def write_raw(self, msg: str):
+        pass
+
+    def cleanup(self):
+        pass
+
+
+class SerialConnector(Connector):
+    port: str
+    mcu_name: str
+    serial_interface: serial.Serial
+
+    def __init__(self, logger: RcutilsLogger, clock: Clock, serial_override: str = ""):
+        super().__init__(logger, clock)
+
+        ports = self._find_ports()
+        mcu_name: str | None = None
+
+        if serial_override:
+            logger.warn(
+                f"using serial_override: `{serial_override}`! this will bypass several checks."
+            )
+            ports = [serial_override]
+            mcu_name = "override"
+
+        if len(ports) <= 0:
+            raise NoValidDeviceException("no valid serial device found")
+        if (l := len(ports)) > 1:
+            raise MultipleValidDevicesException(
+                f"too many ({l}) valid serial devices found"
+            )
+
+        # check each of our ports to make sure one of them is responding
+        port = ports[0]
+        # we might already have a name by now if we overrode earlier
+        mcu_name = mcu_name or self._get_name(port)
+        if not mcu_name:
+            raise NoWorkingDeviceException(
+                f"found {port}, but it did not respond with its name"
+            )
+
+        self.port = port
+        self.mcu_name = mcu_name
+
+        # if we fail at this point, it should crash because we've already tested the port
+        self.serial_interface = serial.Serial(self.port, BAUD_RATE, timeout=1)
+
+    def _find_ports(self) -> list[str]:
+        """
+        Finds all valid ports but does not test them
+
+        returns: all valid ports
+        """
+        comports = serial.tools.list_ports.comports()
+        valid_ports = list(
+            map(  # get just device strings
+                lambda p: p.device,
+                filter(  # make sure we have a known device
+                    lambda p: (p.vid, p.pid) in KNOWN_USBS and p.device is not None,
+                    comports,
+                ),
+            )
+        )
+        self.logger.info(f"found valid MCU ports: [ {', '.join(valid_ports)} ]")
+        return valid_ports
+
+    def _get_name(self, port: str) -> str | None:
+        """
+        Get the name of the MCU (if it works)
+
+        returns: str name of the MCU, None if it doesn't work
+        """
+        # attempt to open the serial port
+        serial_interface: serial.Serial
+        try:
+            self.logger.info(f"asking {port} for its name")
+            serial_interface = serial.Serial(port, BAUD_RATE, timeout=1)
+
+            serial_interface.write(b"can_relay_mode,on\n")
+
+            for i in range(4):
+                self.logger.debug(f"attempt {i + 1} of 4 asking {port} for its name")
+                response = serial_interface.read_until(bytes("\n", "utf8"))
+                try:
+                    if b"can_relay_ready" in response:
+                        args: list[str] = response.decode("utf8").strip().split(",")
+                        if len(args) == 2:
+                            self.logger.info(f"we are talking to {args[1]}")
+                            return args[1]
+                        break
+                except UnicodeDecodeError as e:
+                    self.logger.info(
+                        f"ignoring UnicodeDecodeError when asking for MCU name: {e}"
+                    )
+
+            if serial_interface.is_open:
+                # turn relay mode off if it failed to respond with its name
+                serial_interface.write(b"can_relay_mode,off\n")
+                serial_interface.close()
+        except serial.SerialException as e:
+            self.logger.error(f"SerialException when asking for MCU name: {e}")
+
+        return None
+
+    def read(self) -> tuple[VicCAN | None, str | None]:
+        try:
+            raw = str(self.serial_interface.readline(), "utf8")
+
+            if not raw:
+                return (None, None)
+
+            return (
+                self.string_to_viccan(raw, self.mcu_name),
+                raw,
+            )
+        except serial.SerialException as e:
+            self.logger.error(f"SerialException: {e}")
+            raise DeviceClosedException(f"serial port {self.port} closed unexpectedly")
+        except Exception:
+            return (None, None)  # pretty much no other error matters
+
+    def write(self, msg: VicCAN):
+        self.write_raw(viccan_to_string(msg))
+
+    def write_raw(self, msg: str):
+        self.serial_interface.write(bytes(msg, "utf8"))
+
+    def cleanup(self):
+        self.logger.info(f"closing serial port if open {self.port}")
+        try:
+            if self.serial_interface.is_open:
+                self.serial_interface.close()
+        except Exception as e:
+            self.logger.error(e)
+
+
+class CANConnector(Connector):
+    def __init__(self, logger: RcutilsLogger, clock: Clock, can_override: str):
+        super().__init__(logger, clock)
+
+        self.can_channel: str | None = None
+        self.can_bus: can.BusABC | None = None
+
+        avail = can.interfaces.socketcan.SocketcanBus._detect_available_configs()
+
+        if len(avail) == 0:
+            raise NoValidDeviceException("no CAN interfaces found")
+
+        # filter to busses whose channel matches the can_override
+        if can_override:
+            self.logger.info(f"overrode can interface with {can_override}")
+            avail = list(
+                filter(
+                    lambda b: b.get("channel") == can_override,
+                    avail,
+                )
+            )
+
+        if (l := len(avail)) > 1:
+            channels = ", ".join(str(b.get("channel")) for b in avail)
+            raise MultipleValidDevicesException(
+                f"too many ({l}) CAN interfaces found: [{channels}]"
+            )
+
+        bus = avail[0]
+        self.can_channel = str(bus.get("channel"))
+        self.logger.info(f"found CAN interface '{self.can_channel}'")
+
+        try:
+            self.can_bus = can.Bus(
+                interface="socketcan",
+                channel=self.can_channel,
+                bitrate=1_000_000,
+            )
+        except can.CanError as e:
+            raise NoWorkingDeviceException(
+                f"could not open CAN channel '{self.can_channel}': {e}"
+            )
+
+        if self.can_channel and self.can_channel.startswith("v"):
+            self.logger.warn("CAN interface is likely virtual")
+
+    def read(self) -> tuple[VicCAN | None, str | None]:
+        if not self.can_bus:
+            raise DeviceClosedException("CAN bus not initialized")
+
+        try:
+            message = self.can_bus.recv(timeout=0.0)
+        except can.CanError as e:
+            self.logger.error(f"CAN error while receiving: {e}")
+            raise DeviceClosedException("CAN bus closed unexpectedly")
+
+        if message is None:
+            return (None, None)
+
+        arbitration_id = message.arbitration_id & 0x7FF
+        data_bytes = bytes(message.data)
+
+        mcu_key = (arbitration_id >> 8) & 0b111
+        data_type_key = (arbitration_id >> 6) & 0b11
+        command = arbitration_id & 0x3F
+
+        try:
+            mcu_name = MCU_IDS[mcu_key]
+        except IndexError:
+            self.logger.warn(
+                f"received CAN frame with unknown MCU key {mcu_key}; id=0x{arbitration_id:X}"
+            )
+            return (None, None)
+
+        data: list[float] = []
+
+        try:
+            if data_type_key == 3:
+                data = []
+            elif data_type_key == 0:
+                if len(data_bytes) < 8:
+                    self.logger.warn(
+                        f"received double payload with insufficient length {len(data_bytes)}; dropping frame"
+                    )
+                    return (None, None)
+                (value,) = struct.unpack(">d", data_bytes[:8])
+                data = [float(value)]
+            elif data_type_key == 1:
+                if len(data_bytes) < 8:
+                    self.logger.warn(
+                        f"received float32x2 payload with insufficient length {len(data_bytes)}; dropping frame"
+                    )
+                    return (None, None)
+                v1, v2 = struct.unpack(">ff", data_bytes[:8])
+                data = [float(v1), float(v2)]
+            elif data_type_key == 2:
+                if len(data_bytes) < 8:
+                    self.logger.warn(
+                        f"received int16x4 payload with insufficient length {len(data_bytes)}; dropping frame"
+                    )
+                    return (None, None)
+                i1, i2, i3, i4 = struct.unpack(">hhhh", data_bytes[:8])
+                data = [float(i1), float(i2), float(i3), float(i4)]
+            else:
+                self.logger.warn(
+                    f"received CAN frame with unknown data_type_key {data_type_key}; id=0x{arbitration_id:X}"
+                )
+                return (None, None)
+        except struct.error as e:
+            self.logger.error(f"error unpacking CAN payload: {e}")
+            return (None, None)
+
+        viccan = VicCAN(
+            mcu_name=mcu_name,
+            command_id=int(command),
+            data=data,
+        )
+
+        self.logger.debug(
+            f"received CAN frame id=0x{message.arbitration_id:X}, "
+            f"decoded as VicCAN(mcu_name={viccan.mcu_name}, command_id={viccan.command_id}, data={viccan.data})"
+        )
+
+        return (
+            viccan,
+            f"{viccan.mcu_name},{viccan.command_id},"
+            + ",".join(map(str, list(viccan.data))),
+        )
+
+    def write(self, msg: VicCAN):
+        if not self.can_bus:
+            raise DeviceClosedException("CAN bus not initialized")
+
+        # build 11-bit arbitration ID according to VicCAN spec:
+        # bits 10..8: targeted MCU key
+        # bits 7..6:  data type key
+        # bits 5..0:  command
+
+        # map MCU name to 3-bit key.
+        try:
+            mcu_id = MCU_IDS.index((msg.mcu_name or "").lower())
+        except ValueError:
+            self.logger.error(
+                f"unknown VicCAN mcu_name '{msg.mcu_name}' for CAN frame; dropping message"
+            )
+            return
+
+        # determine data type from length:
+        # 0: double x1, 1: float32 x2, 2: int16 x4, 3: empty
+        match data_len := len(msg.data):
+            case 0:
+                data_type = 3
+                data = bytes()
+            case 1:
+                data_type = 0
+                data = struct.pack(">d", *msg.data)
+            case 2:
+                data_type = 1
+                data = struct.pack(">ff", *msg.data)
+            case 3 | 4:  # 3 gets treated as 4
+                data_type = 2
+                if data_len == 3:
+                    msg.data.append(0)
+                data = struct.pack(">hhhh", *[int(x) for x in msg.data])
+            case _:
+                self.logger.error(
+                    f"unexpected VicCAN data length: {data_len}; dropping message"
+                )
+                return
+
+        # command is limited to 6 bits.
+        command = int(msg.command_id)
+        if command < 0 or command > 0x3F:
+            self.logger.error(
+                f"invalid command_id for CAN frame: {command}; dropping message"
+            )
+            return
+
+        try:
+            can_message = can.Message(
+                arbitration_id=(mcu_id << 8) | (data_type << 6) | command,
+                data=data,
+                is_extended_id=False,
+            )
+        except Exception as e:
+            self.logger.error(f"failed to construct CAN message: {e}")
+            return
+
+        try:
+            self.can_bus.send(can_message)
+            self.logger.debug(
+                f"sent CAN frame id=0x{can_message.arbitration_id:X}, "
+                f"data={list(can_message.data)}"
+            )
+        except can.CanError as e:
+            self.logger.error(f"CAN error while sending: {e}")
+            raise DeviceClosedException("CAN bus closed unexpectedly")
+
+    def write_raw(self, msg: str):
+        self.logger.warn(f"write_raw is not supported for CANConnector. msg: {msg}")
+
+    def cleanup(self):
+        try:
+            if self.can_bus is not None:
+                self.logger.info("shutting down CAN bus")
+                self.can_bus.shutdown()
+        except Exception as e:
+            self.logger.error(e)
+
+
+class MockConnector(Connector):
+    def __init__(self, logger: RcutilsLogger, clock: Clock):
+        super().__init__(logger, clock)
+        # No hardware interface for MockConnector. Publish to `/anchor/from_vic/mock_mcu` instead.
+
+    def read(self) -> tuple[VicCAN | None, str | None]:
+        return (None, None)
+
+    def write(self, msg: VicCAN):
+        pass
+
+    def write_raw(self, msg: str):
+        pass

src/anchor_pkg/anchor_pkg/convert.py

@@ -0,0 +1,65 @@
+from astra_msgs.msg import VicCAN
+from std_msgs.msg import Header
+from builtin_interfaces.msg import Time
+from rclpy.impl.rcutils_logger import RcutilsLogger
+
+
+def string_to_viccan(
+    msg: str, mcu_name: str, logger: RcutilsLogger, time: Time
+) -> VicCAN | None:
+    """
+    Converts the serial string VicCAN format to a ROS2 VicCAN message.
+    Does not fill out the Header of the message.
+    On a failure, it will log at a debug level why it failed and return None.
+    """
+
+    parts: list[str] = msg.strip().split(",")
+
+    # don't need an extra check because len of .split output is always >= 1
+    if not parts[0].startswith("can_relay_"):
+        logger.debug(f"got non-CAN data from {mcu_name}: {msg}")
+        return None
+    elif len(parts) < 3:
+        logger.debug(f"got garbage (not enough parts) CAN data from {mcu_name}: {msg}")
+        return None
+    elif len(parts) > 7:
+        logger.debug(f"got garbage (too many parts) CAN data from {mcu_name}: {msg}")
+        return None
+
+    try:
+        command_id = int(parts[2])
+    except ValueError:
+        logger.debug(
+            f"got garbage (non-integer command id) CAN data from {mcu_name}: {msg}"
+        )
+        return None
+
+    if command_id not in range(64):
+        logger.debug(
+            f"got garbage (wrong command id {command_id}) CAN data from {mcu_name}: {msg}"
+        )
+        return None
+
+    try:
+        return VicCAN(
+            header=Header(
+                stamp=time,
+                frame_id="from_vic",
+            ),
+            mcu_name=parts[1],
+            command_id=command_id,
+            data=[float(x) for x in parts[3:]],
+        )
+    except ValueError:
+        logger.debug(f"got garbage (non-numerical) CAN data from {mcu_name}: {msg}")
+        return None
+
+
+def viccan_to_string(viccan: VicCAN) -> str:
+    """Converts a ROS2 VicCAN message to the serial string VicCAN format."""
+    # make sure we accept 3 digits and treat it as 4
+    if len(viccan.data) == 3:
+        viccan.data.append(0)
+    # go from [ w, x, y, z ] -> ",w,x,y,z" & round to 7 digits max
+    data = "".join([f",{round(val,7)}" for val in viccan.data])
+    return f"can_relay_tovic,{viccan.mcu_name},{viccan.command_id}{data}\n"

src/anchor_pkg/launch/rover.launch.py

@@ -1,164 +1,146 @@
-#!/usr/bin/env python3
-
 from launch import LaunchDescription
-from launch.actions import (
+from launch.actions import DeclareLaunchArgument, Shutdown, IncludeLaunchDescription
-    DeclareLaunchArgument,
-    OpaqueFunction,
-    Shutdown,
-    IncludeLaunchDescription,
-)
-from launch.substitutions import (
-    LaunchConfiguration,
-    ThisLaunchFileDir,
-    PathJoinSubstitution,
-)
-from launch.launch_description_sources import PythonLaunchDescriptionSource
 from launch.conditions import IfCondition
+from launch.substitutions import LaunchConfiguration, PathJoinSubstitution
 from launch_ros.actions import Node
 from launch_ros.substitutions import FindPackageShare
+from launch.launch_description_sources import PythonLaunchDescriptionSource
 
 
-# Prevent making __pycache__ directories
+def generate_launch_description():
-from sys import dont_write_bytecode
+    connector = LaunchConfiguration("connector")
+    serial_override = LaunchConfiguration("serial_override")
+    can_override = LaunchConfiguration("can_override")
+    use_ptz = LaunchConfiguration("use_ptz")
 
-dont_write_bytecode = True
+    ld = LaunchDescription()
 
-
+    # arguments
-def launch_setup(context, *args, **kwargs):
+    ld.add_action(
-    # Retrieve the resolved value of the launch argument 'mode'
+        DeclareLaunchArgument(
-    mode = LaunchConfiguration("mode").perform(context)
+            "connector",
-    nodes = []
+            default_value="auto",
-
+            description="Connector parameter for anchor node (default: 'auto')",
-    if mode == "anchor":
-        # Launch every node and pass "anchor" as the parameter
-
-        nodes.append(
-            Node(
-                package="arm_pkg",
-                executable="arm",  # change as needed
-                name="arm",
-                output="both",
-                parameters=[{"launch_mode": mode}],
-                on_exit=Shutdown(),
         )
     )
-        nodes.append(
+
+    ld.add_action(
+        DeclareLaunchArgument(
+            "serial_override",
+            default_value="",
+            description="Serial port override parameter for anchor node (default: '')",
+        )
+    )
+
+    ld.add_action(
+        DeclareLaunchArgument(
+            "can_override",
+            default_value="",
+            description="CAN network override parameter for anchor node (default: '')",
+        )
+    )
+
+    ld.add_action(
+        DeclareLaunchArgument(
+            "use_ptz",
+            default_value="true",  # must be string for launch system
+            description="Whether to launch PTZ node (default: true)",
+        )
+    )
+
+    ld.add_action(
+        DeclareLaunchArgument(
+            "use_ros2_control",
+            default_value="false",
+            description="Whether to use DiffDriveController for driving instead of direct Twist",
+        )
+    )
+
+    ld.add_action(
+        DeclareLaunchArgument(
+            "rover_platform_override",
+            default_value="",
+            description="Override the rover platform (either clucky or testbed). If unset, hostname is used; defaults to clucky without hostname.",
+            choices=["clucky", "testbed", ""],
+        )
+    )
+
+    # nodes
+    ld.add_action(
         Node(
-                package="core_pkg",
+            package="anchor_pkg",
-                executable="core",  # change as needed
+            executable="anchor",
-                name="core",
+            name="anchor",
             output="both",
             parameters=[
-                    {"launch_mode": mode},
+                {
-                    {"use_ros2_control": LaunchConfiguration("use_ros2_control", default=False)},
+                    "launch_mode": "anchor",
-                    {"is_testbed", LaunchConfiguration("is_testbed", default=False)},
+                    "connector": connector,
+                    "serial_override": serial_override,
+                    "can_override": can_override,
+                }
             ],
             on_exit=Shutdown(),
         )
     )
-        nodes.append(
+
-            Node(
+    ld.add_action(
-                package="core_pkg",
-                executable="ptz",  # change as needed
-                name="ptz",
-                output="both",
-                condition=IfCondition(LaunchConfiguration("use_ptz", default="true")),
-                # Currently don't shutdown all nodes if the PTZ node fails, as it is not critical
-                # on_exit=Shutdown()  # Uncomment if you want to shutdown on PTZ failure
-            )
-        )
-        nodes.append(
-            Node(
-                package="bio_pkg",
-                executable="bio",  # change as needed
-                name="bio",
-                output="both",
-                parameters=[{"launch_mode": mode}],
-                on_exit=Shutdown(),
-            )
-        )
-        nodes.append(
-            Node(
-                package="anchor_pkg",
-                executable="anchor",  # change as needed
-                name="anchor",
-                output="both",
-                parameters=[{"launch_mode": mode}],
-                on_exit=Shutdown(),
-            )
-        )
-    elif mode in ["arm", "core", "bio", "ptz"]:
-        # Only launch the node corresponding to the provided mode.
-        if mode == "arm":
-            nodes.append(
         Node(
             package="arm_pkg",
             executable="arm",
             name="arm",
             output="both",
-                    parameters=[{"launch_mode": mode}],
+            parameters=[{"launch_mode": "anchor"}],
             on_exit=Shutdown(),
         )
     )
-        elif mode == "core":
+
-            nodes.append(
+    ld.add_action(
-                Node(
-                    package="core_pkg",
-                    executable="core",
-                    name="core",
-                    output="both",
-                    parameters=[{"launch_mode": mode}],
-                    on_exit=Shutdown(),
-                )
-            )
-        elif mode == "bio":
-            nodes.append(
         Node(
             package="bio_pkg",
             executable="bio",
             name="bio",
             output="both",
-                    parameters=[{"launch_mode": mode}],
+            parameters=[{"launch_mode": "anchor"}],
             on_exit=Shutdown(),
         )
     )
-        elif mode == "ptz":
+
-            nodes.append(
+    ld.add_action(
+        Node(
+            package="core_pkg",
+            executable="core",
+            name="core",
+            output="both",
+            parameters=[
+                {"launch_mode": "anchor"},
+                {
+                    "use_ros2_control": LaunchConfiguration(
+                        "use_ros2_control", default=False
+                    )
+                },
+                {
+                    "rover_platform_override": LaunchConfiguration(
+                        "rover_platform_override", default="auto"
+                    )
+                },
+            ],
+            on_exit=Shutdown(),
+        )
+    )
+
+    ld.add_action(
         Node(
             package="core_pkg",
             executable="ptz",
             name="ptz",
             output="both",
-                    on_exit=Shutdown(),  # on fail, shutdown if this was the only node to be launched
+            condition=IfCondition(use_ptz),
         )
     )
-    else:
-        # If an invalid mode is provided, print an error.
-        print("Invalid mode provided. Choose one of: arm, core, bio, anchor, ptz.")
 
-    return nodes
+    ld.add_action(
-
+        IncludeLaunchDescription(
-
-def generate_launch_description():
-    declare_arg = DeclareLaunchArgument(
-        "mode",
-        default_value="anchor",
-        description="Launch mode: arm, core, bio, anchor, or ptz",
-    )
-
-    ros2_control_arg = DeclareLaunchArgument(
-        "use_ros2_control",
-        default_value="false",
-        description="Whether to use DiffDriveController for driving instead of direct Twist",
-    )
-
-    testbed_arg = DeclareLaunchArgument(
-        "is_testbed",
-        default_value="false",
-        description="Whether using Testbed (true) or Clucky (false)",
-    )
-
-    rsp = IncludeLaunchDescription(
             PythonLaunchDescriptionSource(
                 PathJoinSubstitution(
                     [
@@ -171,8 +153,10 @@ def generate_launch_description():
             condition=IfCondition(LaunchConfiguration("use_ros2_control")),
             launch_arguments={("hardware_mode", "physical")},
         )
+    )
 
-    controllers = IncludeLaunchDescription(
+    ld.add_action(
+        IncludeLaunchDescription(
             PythonLaunchDescriptionSource(
                 PathJoinSubstitution(
                     [
@@ -185,14 +169,6 @@ def generate_launch_description():
             condition=IfCondition(LaunchConfiguration("use_ros2_control")),
             launch_arguments={("hardware_mode", "physical")},
         )
-
-    return LaunchDescription(
-        [
-            declare_arg,
-            ros2_control_arg,
-            testbed_arg,
-            rsp,
-            controllers,
-            OpaqueFunction(function=launch_setup),
-        ]
     )
+
+    return ld

src/anchor_pkg/package.xml

@@ -2,15 +2,16 @@
 <?xml-model href="http://download.ros.org/schema/package_format3.xsd" schematypens="http://www.w3.org/2001/XMLSchema"?>
 <package format="3">
   <name>anchor_pkg</name>
-  <version>1.0.0</version>
+  <version>0.0.0</version>
   <description>ASTRA VicCAN driver package, using python-can and pyserial.</description>
-  <maintainer email="tristanmcginnis26@gmail.com">tristan</maintainer>
+  <maintainer email="rjm0037@uah.edu">Riley</maintainer>
   <license>AGPL-3.0-only</license>
 
   <depend>rclpy</depend>
 
   <exec_depend>common_interfaces</exec_depend>
   <exec_depend>python3-serial</exec_depend>
+  <exec_depend>python3-can</exec_depend>
 
   <exec_depend>core_pkg</exec_depend>
   <exec_depend>arm_pkg</exec_depend>

src/arm_pkg/arm_pkg/arm_node.py

@@ -12,7 +12,7 @@ from std_msgs.msg import String, Header
 from sensor_msgs.msg import JointState
 from control_msgs.msg import JointJog
 from astra_msgs.msg import SocketFeedback, DigitFeedback, ArmManual  # TODO: Old topics
-from astra_msgs.msg import ArmFeedback, VicCAN, RevMotorState
+from astra_msgs.msg import ArmFeedback, ArmCtrlState, VicCAN, RevMotorState
 
 control_qos = qos.QoSProfile(
     history=qos.QoSHistoryPolicy.KEEP_LAST,
@@ -112,10 +112,10 @@ class ArmNode(Node):
 
         # Control
 
-        # Manual: /arm/manual/joint_jog is published by Basestation or Headless
+        # Manual: /arm/control/joint_jog is published by Basestation or Headless
         self.man_jointjog_sub_ = self.create_subscription(
             JointJog,
-            "/arm/manual/joint_jog",
+            "/arm/control/joint_jog",
             self.jointjog_callback,
             qos_profile=control_qos,
         )
@@ -126,6 +126,13 @@ class ArmNode(Node):
             self.joint_command_callback,
             qos_profile=control_qos,
         )
+        # State: /arm/control/state is published by Basestation or Headless
+        self.man_state_sub_ = self.create_subscription(
+            ArmCtrlState,
+            "/arm/control/state",
+            self.man_state_callback,
+            qos_profile=control_qos,
+        )
 
         # Feedback
 
@@ -145,9 +152,14 @@ class ArmNode(Node):
 
         # Combined Socket and Digit feedback
         self.arm_feedback_new = ArmFeedback()
+        self.arm_feedback_new.axis0_motor.id = 1
+        self.arm_feedback_new.axis1_motor.id = 2
+        self.arm_feedback_new.axis2_motor.id = 3
+        self.arm_feedback_new.axis3_motor.id = 4
 
         # IK Arm pose
         self.saved_joint_state = JointState()
+        self.saved_joint_state.header.frame_id = "base_link"
         self.saved_joint_state.name = self.all_joint_names
         # ... initialize with zeros
         self.saved_joint_state.position = [0.0] * len(self.saved_joint_state.name)
@@ -170,10 +182,54 @@ class ArmNode(Node):
         # Deadzone
         velocities = [vel if abs(vel) > 0.05 else 0.0 for vel in velocities]
 
-        self.send_velocities(velocities, msg.header)
+        self.anchor_tovic_pub_.publish(
+            VicCAN(
+                mcu_name="arm",
+                command_id=39,
+                data=velocities[0:4],
+                header=msg.header,
+            )
+        )
+
+        self.anchor_tovic_pub_.publish(
+            VicCAN(
+                mcu_name="digit",
+                command_id=39,
+                data=velocities[4:6],
+                header=msg.header,
+            )
+        )
+
+        self.anchor_tovic_pub_.publish(
+            VicCAN(
+                mcu_name="digit",
+                command_id=26,
+                data=[velocities[6]],
+                header=msg.header,
+            )
+        )
 
         # TODO: use msg.duration
 
+    def man_state_callback(self, msg: ArmCtrlState):
+        self.anchor_tovic_pub_.publish(
+            VicCAN(
+                mcu_name="arm",
+                command_id=18,
+                data=[1.0 if msg.brake_mode else 0.0],
+                header=Header(stamp=self.get_clock().now().to_msg()),
+            )
+        )
+
+        self.anchor_tovic_pub_.publish(
+            VicCAN(
+                mcu_name="arm",
+                command_id=34,
+                data=[1.0 if msg.laser else 0.0],
+                header=Header(stamp=self.get_clock().now().to_msg()),
+            )
+        )
+
     def joint_command_callback(self, msg: JointState):
         if len(msg.position) < 7 and len(msg.velocity) < 7:
             self.get_logger().debug("Ignoring malformed /joint_command message.")
@@ -199,12 +255,12 @@ class ArmNode(Node):
 
         # Send Axis 0-3
         self.anchor_tovic_pub_.publish(
-            VicCAN(mcu_name="arm", command_id=43, data=velocities[0:3], header=header)
+            VicCAN(mcu_name="arm", command_id=43, data=velocities[0:4], header=header)
         )
         # Send Wrist yaw and roll
         # TODO: Verify embedded
         self.anchor_tovic_pub_.publish(
-            VicCAN(mcu_name="digit", command_id=43, data=velocities[4:5], header=header)
+            VicCAN(mcu_name="digit", command_id=43, data=velocities[4:6], header=header)
         )
         # Send End Effector Gripper
         # TODO: Verify m/s received correctly by embedded
@@ -287,6 +343,8 @@ class ArmNode(Node):
                 )
                 return
 
+        self.arm_feedback_new.header.stamp = msg.header.stamp
+
         match msg.command_id:
             case 53:  # REV SPARK MAX feedback
                 motorId = round(msg.data[0])
@@ -373,11 +431,14 @@ class ArmNode(Node):
                 )
                 return
 
+        self.arm_feedback_new.header.stamp = msg.header.stamp
+
         match msg.command_id:
             case 54:  # Board voltages
                 self.arm_feedback_new.digit_voltage.vbatt = float(msg.data[0]) / 100.0
                 self.arm_feedback_new.digit_voltage.v12 = float(msg.data[1]) / 100.0
                 self.arm_feedback_new.digit_voltage.v5 = float(msg.data[2]) / 100.0
+                self.arm_feedback_new.digit_voltage.header.stamp = msg.header.stamp
             case 55:  # Arm joint positions
                 self.saved_joint_state.position[4] = math.radians(
                     msg.data[0]

src/core_pkg/core_pkg/core_node.py

@@ -1,8 +1,11 @@
 import sys
 import signal
+from typing import Literal, cast
 from scipy.spatial.transform import Rotation
 from math import copysign, pi
 from warnings import deprecated
+from os import getenv
+from socket import gethostname
 
 import rclpy
 from rclpy.node import Node
@@ -54,6 +57,7 @@ class CoreNode(Node):
         56: 4,  # really 3, but viccan
         58: 4,  # ditto
     }
+    rover_platform: Literal["clucky", "testbed"]
 
     def __init__(self):
         super().__init__("core_node")
@@ -68,17 +72,35 @@ class CoreNode(Node):
             self.get_parameter("use_ros2_control").get_parameter_value().bool_value
         )
 
-        self.declare_parameter("is_testbed", False)
+        self.declare_parameter("rover_platform_override", "")
-        self.is_testbed = (
+        rover_platform = (
-            self.get_parameter("is_testbed").get_parameter_value().bool_value
+            self.get_parameter("rover_platform_override")
+            .get_parameter_value()
+            .string_value
         )
+        # Verify rover_platform_override value is valid
+        if rover_platform not in ("clucky", "testbed", ""):
+            # Keeping this here, because I want a value error only if the user manually
+            # overrides using a bad value. If we can't determine it automatically
+            # from hostname, then default to clucky.
+            self.get_logger().fatal(
+                "Invalid rover_platform_override parameter value. If set, must be 'clucky' or 'testbed'."
+            )
+        # Attempt to determine platform from hostname, default to clucky on failure
+        rover_platform = rover_platform or gethostname().lower()
+        if rover_platform not in ("clucky", "testbed"):
+            self.get_logger().info(
+                "rover_platform defaulting to clucky, not overridden and could not determine from hostname."
+            )
+            rover_platform = "clucky"
+        self.rover_platform = cast(Literal["clucky", "testbed"], rover_platform)
 
-        if self.is_testbed:
+        if self.rover_platform == "testbed":
             global TESTBED_WHEELBASE, TESTBED_WHEEL_RADIUS, TESTBED_GEAR_RATIO
             self.wheelbase = TESTBED_WHEELBASE
             self.wheel_radius = TESTBED_WHEEL_RADIUS
             self.gear_ratio = TESTBED_GEAR_RATIO
-        else:
+        else:  # default in case of unset or invalid environment variable
             global CORE_WHEELBASE, CORE_WHEEL_RADIUS, CORE_GEAR_RATIO
             self.wheelbase = CORE_WHEELBASE
             self.wheel_radius = CORE_WHEEL_RADIUS
@@ -167,9 +189,19 @@ class CoreNode(Node):
             Barometer, "/core/feedback/baro", qos_profile=qos.qos_profile_sensor_data
         )
 
+        ###################################################
+        # Timers
+
+        if self.use_ros2_control:
+            self.vel_cmd_timer_ = self.create_timer(0.1, self.vel_cmd_timer_callback)
+
         ###################################################
         # Saved state
 
+        # Controls
+        self._last_joint_command_time = self.get_clock().now()
+        self._last_joint_command_msg = JointState()
+
         # Main Core feedback
         self.feedback_new_state = NewCoreFeedback()
         self.feedback_new_state.fl_motor.id = 1
@@ -242,7 +274,7 @@ class CoreNode(Node):
         #  includes velocities for the commanded joints (ros__parameters.joints).
         # So, this will be much more hacky and less adaptable than I would like it to be.
         if (
-            len(msg.name) != (4 if self.is_testbed else 5)
+            len(msg.name) != (4 if self.rover_platform == "testbed" else 5)
             or len(msg.velocity) != 4
             or len(msg.position) != 0
         ):
@@ -261,16 +293,31 @@ class CoreNode(Node):
             )
             return
 
-        (bl_vel, br_vel, fl_vel, fr_vel) = msg.velocity
+        # A 10 Hz timer callback actually sends these commands to Core for rate limiting
+        # These come from ros2_control at 50 Hz
+        self._last_joint_command_time = self.get_clock().now()
+        self._last_joint_command_msg = msg
 
+    def vel_cmd_timer_callback(self):
+        # Safety timeout for diff_drive_controller commands via topic_based_ros2_control.
+        # It is safe to send stop command here because if self.use_ros2_control,
+        # then this is the only callback that is controlling Core's motors.
+        if self.get_clock().now() - self._last_joint_command_time > Duration(
+            nanoseconds=int(1e8)  # 100ms
+        ):
+            self.send_viccan(20, [0.0, 0.0, 0.0, 0.0])
+            return
+
+        # This order is verified by the subscription callback
+        (bl_vel, br_vel, fl_vel, fr_vel) = self._last_joint_command_msg.velocity
+
+        # Convert wheel rad/s to motor RPM
         bl_rpm = radps_to_rpm(bl_vel) * self.gear_ratio
         br_rpm = radps_to_rpm(br_vel) * self.gear_ratio
         fl_rpm = radps_to_rpm(fl_vel) * self.gear_ratio
         fr_rpm = radps_to_rpm(fr_vel) * self.gear_ratio
 
-        self.send_viccan(
+        self.send_viccan(20, [fl_rpm, bl_rpm, fr_rpm, br_rpm])  # REV Velocity
-            20, [fl_rpm, bl_rpm, fr_rpm, br_rpm]
-        )  # order expected by embedded
 
     def twist_man_callback(self, msg: Twist):
         linear = msg.linear.x  # [-1 1] for forward/back from left stick y
@@ -523,7 +570,7 @@ class CoreNode(Node):
                     motor.velocity = velocity
 
                 # make the fucking shit work
-                if not self.is_testbed:
+                if self.rover_platform == "clucky":
                     joint_state_msg.name.append("left_suspension_joint")
                     joint_state_msg.position.append(0.0)
                     joint_state_msg.velocity.append(0.0)

src/core_pkg/core_pkg/core_ptz.py

@@ -262,7 +262,7 @@ class PtzNode(Node):
             f"[{self.get_clock().now().nanoseconds / 1e9:.2f}] PTZ Node: {message_text}"
         )
         self.debug_pub.publish(msg)
-        self.get_logger().info(message_text)
+        self.get_logger().debug(message_text)
 
     def run_async_func(self, coro):
         """Run an async function in the event loop."""

src/headless_pkg/src/headless_node.py

@@ -18,7 +18,7 @@ from std_msgs.msg import Header
 from geometry_msgs.msg import Twist, TwistStamped
 from control_msgs.msg import JointJog
 from astra_msgs.msg import CoreControl, ArmManual, BioControl
-from astra_msgs.msg import CoreCtrlState
+from astra_msgs.msg import CoreCtrlState, ArmCtrlState
 
 import warnings
 
@@ -177,6 +177,8 @@ class Headless(Node):
         self.ctrl_mode = "core"  # Start in core mode
         self.core_brake_mode = False
         self.core_max_duty = 0.5  # Default max duty cycle (walking speed)
+        self.arm_brake_mode = False
+        self.arm_laser = False
 
         ##################################################
         # Old Topics
@@ -203,7 +205,10 @@ class Headless(Node):
             )
 
             self.arm_manual_pub_ = self.create_publisher(
-                JointJog, "/arm/manual_new", qos_profile=control_qos
+                JointJog, "/arm/control/joint_jog", qos_profile=control_qos
+            )
+            self.arm_state_pub_ = self.create_publisher(
+                ArmCtrlState, "/arm/control/state", qos_profile=control_qos
             )
 
             self.arm_ik_twist_publisher = self.create_publisher(
@@ -361,10 +366,14 @@ class Headless(Node):
             )  # Exponent for finer control (curve)
 
             # This kinda looks dumb being seperate from the following block, but this
-            # maintains the separation between modifying the control message and sending it
+            # maintains the separation between modifying the control message and sending it.
             if self.use_cmd_vel:
-                twist.linear.x *= 1.5
+                # These scaling factors convert raw stick inputs to absolute m/s and rad/s
-                twist.angular.z *= 0.5
+                # values that DiffDriveController will convert to motor RPM, rather than
+                # the plain Twist, which just sends the stick values as duty cycle and
+                # sends that scaled to the motors.
+                twist.linear.x *= 1.0
+                twist.angular.z *= 1.5
 
             # Publish
             if self.use_cmd_vel:
@@ -582,13 +591,26 @@ class Headless(Node):
             )
 
             # A: brake
-            # TODO: Brake mode
+            new_brake_mode = button_a
 
-            # Y: linear actuator
+            # X: laser
-            # TODO: linear actuator
+            new_laser = button_x
 
             self.arm_manual_pub_.publish(arm_input)
 
+            # Only publish state if needed
+            if new_brake_mode != self.arm_brake_mode or new_laser != self.arm_laser:
+                self.arm_brake_mode = new_brake_mode
+                self.arm_laser = new_laser
+                state_msg = ArmCtrlState()
+                state_msg.brake_mode = bool(self.arm_brake_mode)
+                state_msg.laser = bool(self.arm_laser)
+
+                self.arm_state_pub_.publish(state_msg)
+                self.get_logger().info(
+                    f"[Arm State] Brake: {self.arm_brake_mode}, Laser: {self.arm_laser}"
+                )
+
         # IK (ONLY NEW)
         # =============
 

treefmt.nix

@@ -0,0 +1,8 @@
+{ pkgs, ... }:
+{
+  projectRootFile = "flake.nix";
+  programs = {
+    nixfmt.enable = true;
+    black.enable = true;
+  };
+}