revert: fix(anchor): serial reads are now non-blocking

This reverts commit fc2ba5f8d1.

reason: making serail reads non-blocking caused serial data issues
because sometimes it would exit before actually seeing a newline

README.md

@@ -60,6 +60,33 @@ $ ros2 launch anchor_pkg rover.launch.py  # Must be run on a computer connected
 $ ros2 run headless_pkg headless_full  # Optionally run in a separate shell on the same or different computer.
 ```
 
+### Using the Mock Connector
+
+Anchor provides a mock connector meant for testing and scripting purposes. You can select the mock connector by running anchor with this command:
+
+```bash
+$ ros2 launch anchor_pkg rover.launch.py connector:="mock"
+```
+
+To see all data that would be sent over the CAN network (and thus to the microcontrollers), use this command:
+
+```bash
+$ ros2 topic echo /anchor/to_vic/debug
+```
+
+To send data to the mock connector (as if you were a ROS2 node), use the normal relay topic:
+
+```bash
+$ ros2 topic pub /anchor/to_vic/relay astra_msgs/msg/VicCAN '{mcu_name: "core", command_id: 50, data: [0.0, 2.0, 0.0, 1.0]}'
+
+```
+
+To send data to the mock connector (as if you were a microcontroller), publish to the dedicated topic:
+
+```bash
+$ ros2 topic pub /anchor/from_vic/mock_mcu astra_msgs/msg/VicCAN '{mcu_name: "arm", command_id: 55, data: [0.0, 450.0, 900.0, 0.0]}'
+```
+
 ### Testing Serial
 
 You can fake the presence of a Serial device (i.e., MCU) by using the following command:
@@ -68,10 +95,31 @@ You can fake the presence of a Serial device (i.e., MCU) by using the following
 $ socat -dd -v pty,rawer,crnl,link=/tmp/ttyACM9 pty,rawer,crnl,link=/tmp/ttyOUT
 ```
 
-When you go to run anchor, use the `PORT_OVERRIDE` environment variable to point it to the fake serial port, like so:
+When you go to run anchor, use the `serial_override` ROS2 parameter to point it to the fake serial port, like so:
 
 ```bash
-$ PORT_OVERRIDE=/tmp/ttyACM9 ros2 launch anchor_pkg rover.launch.py
+$ ros2 launch anchor_pkg rover.launch.py connector:=serial serial_override:=/tmp/ttyACM9
+```
+
+### Testing CAN
+
+You can create a virtual CAN network by using the following commands to create and then enable it:
+
+```bash
+sudo ip link add dev vcan0 type vcan
+sudo ip link set vcan0 up
+```
+
+When you go to run anchor, use the `can_override` ROS2 parameter to point it to the virtual CAN network, like so:
+
+```bash
+$ ros2 launch anchor_pkg rover.launch.py connector:=can can_override:=vcan0
+```
+
+Once you're done, you should delete the virtual network so that anchor doesn't get confused if you plug in a real CAN adapter:
+
+```bash
+$ sudo ip link delete vcan0
 ```
 
 ### Connecting the GuliKit Controller

auto_start/auto_start_anchor.sh

@@ -1,12 +1,12 @@
 #!/usr/bin/env bash
 set -e
 
-SCRIPT_DIR=$( cd -- "$( dirname -- "${BASH_SOURCE[0]}" )" &> /dev/null && pwd )
+SCRIPT_DIR=$(cd -- "$(dirname -- "${BASH_SOURCE[0]}")" &>/dev/null && pwd)
 
 # Wait for a network interface to be up (not necessarily online)
 while ! ip link show | grep -q "state UP"; do
-    echo "[INFO] Waiting for active network interface..."
-    sleep 1
+  echo "[INFO] Waiting for active network interface..."
+  sleep 1
 done
 
 echo "[INFO] Network interface is up!"
@@ -16,9 +16,9 @@ echo "[INFO] Starting ROS node..."
 
 # Source ROS 2 Humble setup script
 if command -v nixos-rebuild; then
-    echo "[INFO] running on NixOS"
+  echo "[INFO] running on NixOS"
 else
-    source /opt/ros/humble/setup.bash
+  source /opt/ros/humble/setup.bash
 fi
 
 # Source your workspace setup script

auto_start/auto_start_headless_full.sh

@@ -1,12 +1,12 @@
 #!/usr/bin/env bash
 set -e
 
-SCRIPT_DIR=$( cd -- "$( dirname -- "${BASH_SOURCE[0]}" )" &> /dev/null && pwd )
+SCRIPT_DIR=$(cd -- "$(dirname -- "${BASH_SOURCE[0]}")" &>/dev/null && pwd)
 
 # Wait for a network interface to be up (not necessarily online)
 while ! ip link show | grep -q "state UP"; do
-    echo "[INFO] Waiting for active network interface..."
-    sleep 1
+  echo "[INFO] Waiting for active network interface..."
+  sleep 1
 done
 
 echo "[INFO] Network interface is up!"
@@ -16,9 +16,9 @@ echo "[INFO] Starting ROS node..."
 
 # Source ROS 2 Humble setup script
 if command -v nixos-rebuild; then
-    echo "[INFO] running on NixOS"
+  echo "[INFO] running on NixOS"
 else
-    source /opt/ros/humble/setup.bash
+  source /opt/ros/humble/setup.bash
 fi
 
 # Source your workspace setup script
@@ -26,4 +26,3 @@ source $SCRIPT_DIR/../install/setup.bash
 
 # Launch the ROS 2 node
 ros2 run headless_pkg headless_full
-

auto_start/start_rosbag.sh

@@ -1,26 +1,25 @@
 #!/usr/bin/env bash
 set -e
 
-SCRIPT_DIR=$( cd -- "$( dirname -- "${BASH_SOURCE[0]}" )" &> /dev/null && pwd )
+SCRIPT_DIR=$(cd -- "$(dirname -- "${BASH_SOURCE[0]}")" &>/dev/null && pwd)
 
-[[ -z "$ANCHOR_WS" ]] && ANCHOR_WS="$SCRIPT_DIR/.."
-[[ -z "$AUTONOMY_WS" ]] && AUTONOMY_WS="$HOME/rover-Autonomy"
+[[ -z $ANCHOR_WS ]] && ANCHOR_WS="$SCRIPT_DIR/.."
+[[ -z $AUTONOMY_WS ]] && AUTONOMY_WS="$HOME/rover-Autonomy"
 BAG_LOCATION="$HOME/bags/autostart"
-[[ ! -d "$BAG_LOCATION" ]] && mkdir -p "$BAG_LOCATION"
+[[ ! -d $BAG_LOCATION ]] && mkdir -p "$BAG_LOCATION"
 
 # Wait for a network interface to be up (not necessarily online)
 while ! ip link show | grep -q "state UP"; do
-    echo "[INFO] Waiting for active network interface..."
-    sleep 1
+  echo "[INFO] Waiting for active network interface..."
+  sleep 1
 done
 
 echo "[INFO] Network interface is up!"
 
-
 if command -v nixos-rebuild; then
-    echo "[INFO] running on NixOS"
+  echo "[INFO] running on NixOS"
 else
-    source /opt/ros/humble/setup.bash
+  source /opt/ros/humble/setup.bash
 fi
 source $ANCHOR_WS/install/setup.bash
 [[ -f $AUTONOMY_WS/install/setup.bash ]] && source $AUTONOMY_WS/install/setup.bash

flake.lock

@@ -24,16 +24,16 @@
         "nixpkgs": "nixpkgs"
       },
       "locked": {
-        "lastModified": 1770108954,
-        "narHash": "sha256-VBj6bd4LPPSfsZJPa/UPPA92dOs6tmQo0XZKqfz/3W4=",
+        "lastModified": 1775216071,
+        "narHash": "sha256-PrPW70Fh1uLx3JxNV/NLeXjUhgfrZmi7ac8LJOlS0q4=",
         "owner": "lopsided98",
         "repo": "nix-ros-overlay",
-        "rev": "3d05d46451b376e128a1553e78b8870c75d7753a",
+        "rev": "197a2b55c4ed24f8b885a5b20b65f426fb6d57ca",
         "type": "github"
       },
       "original": {
         "owner": "lopsided98",
-        "ref": "develop",
+        "ref": "master",
         "repo": "nix-ros-overlay",
         "type": "github"
       }
@@ -60,7 +60,8 @@
         "nixpkgs": [
           "nix-ros-overlay",
           "nixpkgs"
-        ]
+        ],
+        "treefmt-nix": "treefmt-nix"
       }
     },
     "systems": {
@@ -77,6 +78,26 @@
         "repo": "default",
         "type": "github"
       }
+    },
+    "treefmt-nix": {
+      "inputs": {
+        "nixpkgs": [
+          "nixpkgs"
+        ]
+      },
+      "locked": {
+        "lastModified": 1773297127,
+        "narHash": "sha256-6E/yhXP7Oy/NbXtf1ktzmU8SdVqJQ09HC/48ebEGBpk=",
+        "owner": "numtide",
+        "repo": "treefmt-nix",
+        "rev": "71b125cd05fbfd78cab3e070b73544abe24c5016",
+        "type": "github"
+      },
+      "original": {
+        "owner": "numtide",
+        "repo": "treefmt-nix",
+        "type": "github"
+      }
     }
   },
   "root": "root",

flake.nix

@@ -2,8 +2,13 @@
   description = "Development environment for ASTRA Anchor";
 
   inputs = {
-    nix-ros-overlay.url = "github:lopsided98/nix-ros-overlay/develop";
+    nix-ros-overlay.url = "github:lopsided98/nix-ros-overlay/master";
     nixpkgs.follows = "nix-ros-overlay/nixpkgs"; # IMPORTANT!!!
+
+    treefmt-nix = {
+      url = "github:numtide/treefmt-nix";
+      inputs.nixpkgs.follows = "nixpkgs";
+    };
   };
 
   outputs =
@@ -11,7 +16,8 @@
       self,
       nix-ros-overlay,
       nixpkgs,
-    }:
+      ...
+    }@inputs:
     nix-ros-overlay.inputs.flake-utils.lib.eachDefaultSystem (
       system:
       let
@@ -25,9 +31,12 @@
           name = "ASTRA Anchor";
           packages = with pkgs; [
             colcon
+            socat
+            can-utils
             (python313.withPackages (
               p: with p; [
                 pyserial
+                python-can
                 pygame
                 scipy
                 crccheck
@@ -61,7 +70,7 @@
                   moveit-msgs
                   moveit-ros-planning
                   moveit-ros-planning-interface
-		  moveit-ros-visualization
+                  moveit-ros-visualization
                   moveit-configs-utils
                   moveit-ros-move-group
                   moveit-servo
@@ -72,7 +81,7 @@
                   ompl
                   joy
                   ros2-controllers
-		  chomp-motion-planner
+                  chomp-motion-planner
                 ];
               }
             )
@@ -83,11 +92,14 @@
             export QT_X11_NO_MITSHM=1
           '';
         };
+
+        formatter = (inputs.treefmt-nix.lib.evalModule pkgs ./treefmt.nix).config.build.wrapper;
       }
     );
 
   nixConfig = {
-    extra-substituters = [ "https://ros.cachix.org" ];
-    extra-trusted-public-keys = [ "ros.cachix.org-1:dSyZxI8geDCJrwgvCOHDoAfOm5sV1wCPjBkKL+38Rvo=" ];
+    # Cache to pull ros packages from
+    extra-substituters = [ "https://ros.cachix.org" "https://attic.iid.ciirc.cvut.cz/ros" ];
+    extra-trusted-public-keys = [ "ros.cachix.org-1:dSyZxI8geDCJrwgvCOHDoAfOm5sV1wCPjBkKL+38Rvo=" "ros:JR95vUYsShSqfA1VTYoFt1Nz6uXasm5QrcOsGry9f6Q=" ];
   };
 }

scripts/reset-repo.bash

@@ -0,0 +1,38 @@
+#!/usr/bin/env bash
+
+repo_root="$(git rev-parse --show-toplevel)"
+
+if [[ -z $repo_root ]]; then
+  echo "script must be run from within a git repo" >&2
+  exit 1
+fi
+
+cd $repo_root
+
+echo "this will nuke all of your current un-commited git changes, including any changes to submodules and any gitignored files. is this okay? (y/N)"
+read okay
+
+if [[ $okay != "y" ]]; then
+  echo "you didn't say exactly 'y'. aborting." >&2
+  exit 2
+fi
+
+echo
+
+echo "ok say goodbye to everything in this repo"
+git submodule deinit --all -f && echo "- submodules gone"
+git clean -fdx && echo "- gitignored changes gone"
+git add -A
+git reset HEAD --hard && echo "- everything else gone"
+git submodule update --init --recursive && echo "- brought the submodules back"
+echo
+
+echo "in theory that should've done it. let's make sure"
+status=$(git status --porcelain)
+echo $status
+if [[ -z $status ]]; then
+  echo "nice, all clean!"
+else
+  echo "uhh that's not supposed to be there. this is probably a bug in this script. good luck!" >&2
+  exit 3
+fi

scripts/test-connectors.bash

@@ -0,0 +1,463 @@
+#!/usr/bin/env bash
+
+# test script for anchor connectors (mock, serial, CAN)
+
+set -o pipefail
+
+repo_root="$(git rev-parse --show-toplevel)"
+
+if [[ -z $repo_root ]]; then
+  echo "script must be run from within the rover-ros2 repo" >&2
+  exit 1
+fi
+
+cd "$repo_root"
+
+# colors
+BOLD='\033[1m'
+RED='\033[1;31m'
+GREEN='\033[1;32m'
+YELLOW='\033[1;33m'
+NC='\033[0m'
+
+TESTS_PASSED=0
+TESTS_FAILED=0
+
+log() {
+  echo -e "${BOLD}${YELLOW}info:${NC} ${1}"
+}
+
+pass() {
+  echo -e "${BOLD}${GREEN}pass:${NC} ${1}"
+  TESTS_PASSED=$((TESTS_PASSED + 1))
+}
+
+fail() {
+  echo -e "${BOLD}${RED}fail:${NC} ${1}"
+  TESTS_FAILED=$((TESTS_FAILED + 1))
+}
+
+cleanup() {
+  log "cleaning up"
+  if [[ -n $ANCHOR_PID ]]; then
+    kill -INT -- -"$ANCHOR_PID" 2>/dev/null || true
+    wait "$ANCHOR_PID" 2>/dev/null || true
+  fi
+  if [[ -n $SOCAT_PID ]]; then
+    kill -INT "$SOCAT_PID" 2>/dev/null || true
+    wait "$SOCAT_PID" 2>/dev/null || true
+  fi
+  rm -f /tmp/ttyACM9 /tmp/ttyOUT 2>/dev/null || true
+}
+
+trap cleanup EXIT
+
+source_ros2() {
+  source install/setup.bash
+}
+
+wait_for_topic() {
+  local topic="$1"
+  local timeout="${2:-5}"
+  local count=0
+  while ! ros2 topic list 2>/dev/null | grep -q "^${topic}$"; do
+    sleep 0.5
+    count=$((count + 1))
+    if [[ $count -ge $((timeout * 2)) ]]; then
+      return 1
+    fi
+  done
+  return 0
+}
+
+# run a ROS pub/echo test
+# usage: ros_pubsub_test <echo_topic> <pub_topic> <msg_type> <msg_data>
+# returns the echo output via stdout
+ros_pubsub_test() {
+  local echo_topic="$1"
+  local pub_topic="$2"
+  local msg_type="$3"
+  local msg_data="$4"
+
+  timeout 5 bash -c "
+    ros2 topic echo --once $echo_topic &
+    ECHO_PID=\$!
+    sleep 0.5
+    ros2 topic pub --once $pub_topic $msg_type \"$msg_data\" >/dev/null 2>&1
+    wait \$ECHO_PID
+  " 2>/dev/null || true
+}
+
+test_mock_connector() {
+  log "testing mock connector"
+
+  log "starting anchor with mock connector"
+  setsid ros2 run anchor_pkg anchor --ros-args -p connector:=mock &
+  ANCHOR_PID=$!
+  sleep 2
+
+  if ! kill -0 "$ANCHOR_PID" 2>/dev/null; then
+    fail "mock connector: anchor failed to start"
+    return 1
+  fi
+
+  if ! wait_for_topic "/anchor/to_vic/relay" 10; then
+    fail "mock connector: topics not available"
+    kill -INT -- -"$ANCHOR_PID" 2>/dev/null || true
+    return 1
+  fi
+
+  log "anchor started successfully"
+
+  # test: relay -> debug
+  log "testing relay -> debug"
+  local output
+  output=$(ros_pubsub_test "/anchor/to_vic/debug" "/anchor/to_vic/relay" \
+    "astra_msgs/msg/VicCAN" '{mcu_name: \"core\", command_id: 50, data: [1.0, 2.0, 3.0, 4.0]}')
+
+  if [[ -n $output ]] && echo "$output" | grep -q "can_relay_tovic,core,50"; then
+    pass "mock connector: relay -> debug"
+  else
+    fail "mock connector: relay -> debug"
+  fi
+
+  # test: mock_mcu -> from_vic/core
+  log "testing mock_mcu (core) -> from_vic/core"
+  output=$(ros_pubsub_test "/anchor/from_vic/core" "/anchor/from_vic/mock_mcu" \
+    "astra_msgs/msg/VicCAN" '{mcu_name: \"core\", command_id: 10, data: [100.0, 200.0]}')
+
+  if [[ -n $output ]] && echo "$output" | grep -q "mcu_name: core" && echo "$output" | grep -q "command_id: 10"; then
+    pass "mock connector: mock_mcu -> from_vic/core"
+  else
+    fail "mock connector: mock_mcu -> from_vic/core"
+  fi
+
+  # test: mock_mcu -> from_vic/arm
+  log "testing mock_mcu (arm) -> from_vic/arm"
+  output=$(ros_pubsub_test "/anchor/from_vic/arm" "/anchor/from_vic/mock_mcu" \
+    "astra_msgs/msg/VicCAN" '{mcu_name: \"arm\", command_id: 55, data: [0.0, 450.0, 900.0, 0.0]}')
+
+  if [[ -n $output ]] && echo "$output" | grep -q "mcu_name: arm" && echo "$output" | grep -q "command_id: 55"; then
+    pass "mock connector: mock_mcu -> from_vic/arm"
+  else
+    fail "mock connector: mock_mcu -> from_vic/arm"
+  fi
+
+  # test: mock_mcu -> from_vic/bio
+  log "testing mock_mcu (citadel) -> from_vic/bio"
+  output=$(ros_pubsub_test "/anchor/from_vic/bio" "/anchor/from_vic/mock_mcu" \
+    "astra_msgs/msg/VicCAN" '{mcu_name: \"citadel\", command_id: 20, data: [5.0]}')
+
+  if echo "$output" | grep -q "mcu_name: citadel" && echo "$output" | grep -q "command_id: 20"; then
+    pass "mock connector: mock_mcu -> from_vic/bio"
+  else
+    fail "mock connector: mock_mcu -> from_vic/bio"
+  fi
+
+  # test: relay_string -> debug
+  log "testing relay_string -> debug"
+  output=$(ros_pubsub_test "/anchor/to_vic/debug" "/anchor/to_vic/relay_string" \
+    "std_msgs/msg/String" '{data: \"test_raw_string_data\"}')
+
+  if [[ -n $output ]] && echo "$output" | grep -q "test_raw_string_data"; then
+    pass "mock connector: relay_string -> debug"
+  else
+    fail "mock connector: relay_string -> debug"
+  fi
+
+  kill -INT -- -"$ANCHOR_PID" 2>/dev/null || true
+  wait "$ANCHOR_PID" 2>/dev/null || true
+  ANCHOR_PID=""
+}
+
+test_serial_connector() {
+  log "testing serial connector"
+
+  log "creating virtual serial ports with socat"
+  socat pty,raw,echo=0,link=/tmp/ttyACM9 pty,raw,echo=0,link=/tmp/ttyOUT 2>/dev/null &
+  SOCAT_PID=$!
+  sleep 2
+
+  if ! kill -0 "$SOCAT_PID" 2>/dev/null; then
+    fail "serial connector: failed to create virtual serial ports"
+    return 1
+  fi
+
+  log "starting anchor with serial connector (override: /tmp/ttyACM9)"
+  setsid ros2 run anchor_pkg anchor --ros-args -p connector:=serial -p serial_override:=/tmp/ttyACM9 &
+  ANCHOR_PID=$!
+  sleep 2
+
+  if ! kill -0 "$ANCHOR_PID" 2>/dev/null; then
+    fail "serial connector: anchor failed to start"
+    kill -INT "$SOCAT_PID" 2>/dev/null || true
+    return 1
+  fi
+
+  if ! wait_for_topic "/anchor/to_vic/relay" 10; then
+    fail "serial connector: topics not available"
+    kill -INT -- -"$ANCHOR_PID" 2>/dev/null || true
+    kill -INT "$SOCAT_PID" 2>/dev/null || true
+    return 1
+  fi
+
+  pass "serial connector: anchor starts with virtual serial"
+
+  # test: relay -> serial output (VicCAN encoding)
+  log "testing relay -> serial output"
+
+  local serial_out_file
+  serial_out_file=$(mktemp)
+
+  # Start head first (blocks waiting for input), then publish
+  timeout 5 head -n1 /tmp/ttyOUT >"$serial_out_file" &
+  local head_pid=$!
+  sleep 0.3
+  ros2 topic pub --once /anchor/to_vic/relay astra_msgs/msg/VicCAN \
+    '{mcu_name: "core", command_id: 30, data: [1.0, 2.0, 3.0, 4.0]}' >/dev/null 2>&1
+  wait $head_pid 2>/dev/null || true
+
+  local serial_out
+  serial_out=$(cat "$serial_out_file")
+  rm -f "$serial_out_file"
+
+  if [[ -n $serial_out ]] && echo "$serial_out" | grep -q "can_relay_tovic,core,30"; then
+    pass "serial connector: relay -> serial output"
+  else
+    fail "serial connector: relay -> serial output (got: $serial_out)"
+  fi
+
+  # test: serial input -> from_vic/core
+  log "testing serial input -> from_vic/core"
+
+  local output
+  output=$(timeout 5 bash -c '
+    ros2 topic echo --once /anchor/from_vic/core &
+    ECHO_PID=$!
+    sleep 0.5
+    echo "can_relay_fromvic,core,15,10.0,20.0,30.0,40.0" > /tmp/ttyOUT
+    sleep 0.5
+    echo "can_relay_fromvic,core,15,10.0,20.0,30.0,40.0" > /tmp/ttyOUT
+    wait $ECHO_PID
+  ' 2>/dev/null) || true
+
+  if echo "$output" | grep -q "mcu_name: core" && echo "$output" | grep -q "command_id: 15"; then
+    pass "serial connector: serial input -> from_vic/core"
+  else
+    fail "serial connector: serial input -> from_vic/core (got: $output)"
+  fi
+
+  # test: relay_string -> debug
+  log "testing relay_string -> debug"
+  output=$(ros_pubsub_test "/anchor/to_vic/debug" "/anchor/to_vic/relay_string" \
+    "std_msgs/msg/String" '{data: \"serial_test_string\"}')
+
+  if [[ -n $output ]] && echo "$output" | grep -q "serial_test_string"; then
+    pass "serial connector: relay_string -> debug"
+  else
+    fail "serial connector: relay_string -> debug"
+  fi
+
+  kill -INT -- -"$ANCHOR_PID" 2>/dev/null || true
+  wait "$ANCHOR_PID" 2>/dev/null || true
+  ANCHOR_PID=""
+  kill -INT "$SOCAT_PID" 2>/dev/null || true
+  wait "$SOCAT_PID" 2>/dev/null || true
+  SOCAT_PID=""
+}
+
+test_can_connector() {
+  log "testing CAN connector"
+
+  log "starting anchor with CAN connector (override: vcan0)"
+  setsid ros2 run anchor_pkg anchor --ros-args -p connector:=can -p can_override:=vcan0 &
+  ANCHOR_PID=$!
+  sleep 2
+
+  if ! kill -0 "$ANCHOR_PID" 2>/dev/null; then
+    fail "CAN connector: anchor failed to start"
+    return 1
+  fi
+
+  if ! wait_for_topic "/anchor/to_vic/relay" 10; then
+    fail "CAN connector: topics not available"
+    kill -INT -- -"$ANCHOR_PID" 2>/dev/null || true
+    return 1
+  fi
+
+  log "anchor started successfully"
+  sleep 1
+
+  # test: relay -> CAN bus
+  # core=1, int16x4=2, cmd=30 -> id = (1<<8)|(2<<6)|30 = 0x19E
+  log "testing relay -> CAN bus"
+
+  local output
+  output=$(timeout 8 bash -c '
+    candump -n 1 vcan0 &
+    DUMP_PID=$!
+    sleep 1
+    ros2 topic pub --once /anchor/to_vic/relay astra_msgs/msg/VicCAN "{mcu_name: \"core\", command_id: 30, data: [1, 2, 3, 4]}" >/dev/null 2>&1
+    sleep 0.5
+    ros2 topic pub --once /anchor/to_vic/relay astra_msgs/msg/VicCAN "{mcu_name: \"core\", command_id: 30, data: [1, 2, 3, 4]}" >/dev/null 2>&1
+    wait $DUMP_PID
+  ' 2>/dev/null) || true
+
+  if echo "$output" | grep -qi "19E"; then
+    pass "CAN connector: relay -> CAN bus"
+  else
+    fail "CAN connector: relay -> CAN bus (got: $output)"
+  fi
+
+  # test: CAN -> from_vic/core
+  log "testing CAN bus -> from_vic/core"
+
+  output=$(timeout 5 bash -c '
+    ros2 topic echo --once /anchor/from_vic/core &
+    ECHO_PID=$!
+    sleep 1
+    cansend vcan0 18F#000A0014001E0028
+    sleep 0.5
+    cansend vcan0 18F#000A0014001E0028
+    wait $ECHO_PID
+  ' 2>/dev/null) || true
+
+  if echo "$output" | grep -q "mcu_name: core" && echo "$output" | grep -q "command_id: 15"; then
+    pass "CAN connector: CAN -> from_vic/core"
+  else
+    fail "CAN connector: CAN -> from_vic/core"
+  fi
+
+  # test: CAN -> from_vic/arm
+  log "testing CAN bus -> from_vic/arm"
+
+  output=$(timeout 5 bash -c '
+    ros2 topic echo --once /anchor/from_vic/arm &
+    ECHO_PID=$!
+    sleep 1
+    cansend vcan0 294#00640096012C01F4
+    sleep 0.5
+    cansend vcan0 294#00640096012C01F4
+    wait $ECHO_PID
+  ' 2>/dev/null) || true
+
+  if echo "$output" | grep -q "mcu_name: arm" && echo "$output" | grep -q "command_id: 20"; then
+    pass "CAN connector: CAN -> from_vic/arm"
+  else
+    fail "CAN connector: CAN -> from_vic/arm"
+  fi
+
+  # test: CAN double data type (data_type_key=0)
+  log "testing CAN double data type"
+
+  output=$(timeout 8 bash -c '
+    ros2 topic echo --once /anchor/from_vic/core &
+    ECHO_PID=$!
+    sleep 1
+    cansend vcan0 105#3FF0000000000000
+    sleep 0.5
+    cansend vcan0 105#3FF0000000000000
+    sleep 0.5
+    cansend vcan0 105#3FF0000000000000
+    wait $ECHO_PID
+  ' 2>/dev/null) || true
+
+  if echo "$output" | grep -q "mcu_name: core" && echo "$output" | grep -q "command_id: 5"; then
+    pass "CAN connector: double data type"
+  else
+    fail "CAN connector: double data type"
+  fi
+
+  # test: CAN float32x2 data type (data_type_key=1)
+  log "testing CAN float32x2 data type"
+
+  output=$(timeout 8 bash -c '
+    ros2 topic echo --once /anchor/from_vic/core &
+    ECHO_PID=$!
+    sleep 1
+    cansend vcan0 14A#3F80000040000000
+    sleep 0.5
+    cansend vcan0 14A#3F80000040000000
+    sleep 0.5
+    cansend vcan0 14A#3F80000040000000
+    wait $ECHO_PID
+  ' 2>/dev/null) || true
+
+  if echo "$output" | grep -q "mcu_name: core" && echo "$output" | grep -q "command_id: 10"; then
+    pass "CAN connector: float32x2 data type"
+  else
+    fail "CAN connector: float32x2 data type"
+  fi
+
+  kill -INT -- -"$ANCHOR_PID" 2>/dev/null || true
+  wait "$ANCHOR_PID" 2>/dev/null || true
+  ANCHOR_PID=""
+}
+
+check_prerequisites() {
+  log "checking prerequisites"
+  local missing=0
+
+  if [[ ! -f install/setup.bash ]]; then
+    fail "install/setup.bash not found; run 'colcon build --symlink-install' first"
+    missing=1
+  fi
+
+  if ! command -v socat &>/dev/null; then
+    fail "socat not found; install it or use 'nix develop'"
+    missing=1
+  fi
+
+  if ! command -v cansend &>/dev/null || ! command -v candump &>/dev/null; then
+    fail "can-utils (cansend/candump) not found; install it or use 'nix develop'"
+    missing=1
+  fi
+
+  if ! ip link show vcan0 &>/dev/null; then
+    fail "vcan0 interface not found"
+    log "  create it with:"
+    log "    sudo ip link add dev vcan0 type vcan"
+    log "    sudo ip link set vcan0 up"
+    missing=1
+  elif ! ip link show vcan0 | grep -q ",UP"; then
+    fail "vcan0 exists but is not UP"
+    log "  enable it with: sudo ip link set vcan0 up"
+    missing=1
+  fi
+
+  if [[ $missing -eq 1 ]]; then
+    echo ""
+    log "prerequisites not met"
+    exit 1
+  fi
+
+  log "all prerequisites met"
+}
+
+main() {
+  echo ""
+  log "anchor connector test suite"
+  echo ""
+
+  check_prerequisites
+
+  log "sourcing ROS2 workspace"
+  source_ros2
+
+  test_mock_connector
+  test_serial_connector
+  test_can_connector
+
+  echo ""
+  log "test summary"
+  echo -e "${BOLD}${GREEN}passed:${NC} $TESTS_PASSED"
+  echo -e "${BOLD}${RED}failed:${NC} $TESTS_FAILED"
+  echo ""
+
+  if [[ $TESTS_FAILED -gt 0 ]]; then
+    exit 1
+  fi
+  exit 0
+}
+
+main "$@"

src/anchor_pkg/anchor_pkg/anchor_node.py

@@ -1,28 +1,21 @@
+from warnings import deprecated
 import rclpy
 from rclpy.node import Node
-from rclpy.executors import ExternalShutdownException
-from std_srvs.srv import Empty
+from rclpy.executors import ExternalShutdownException, SingleThreadedExecutor
+from rcl_interfaces.msg import ParameterDescriptor, ParameterType
 
-import signal
-import time
-import atexit
+from .connector import (
+    Connector,
+    MockConnector,
+    SerialConnector,
+    CANConnector,
+    NoValidDeviceException,
+    NoWorkingDeviceException,
+)
+from .convert import string_to_viccan, viccan_to_string
 
-import serial
-import serial.tools.list_ports
-import os
-import sys
-import threading
-import glob
-
-from std_msgs.msg import String, Header
 from astra_msgs.msg import VicCAN
-
-KNOWN_USBS = [
-    (0x2E8A, 0x00C0),  # Raspberry Pi Pico
-    (0x1A86, 0x55D4),  # Adafruit Feather ESP32 V2
-    (0x10C4, 0xEA60),  # DOIT ESP32 Devkit V1
-    (0x1A86, 0x55D3),  # ESP32 S3 Development Board
-]
+from std_msgs.msg import String
 
 
 class Anchor(Node):
@@ -36,330 +29,227 @@ class Anchor(Node):
         - VicCAN messages for Arm node
     * /anchor/from_vic/bio
         - VicCAN messages for Bio node
+    * /anchor/to_vic/debug
+        - A string copy of the messages published to ./relay are published here
 
     Subscribers:
     * /anchor/from_vic/mock_mcu
-        - For testing without an actual MCU, publish strings here as if they came from an MCU
+        - For testing without an actual MCU, publish VicCAN messages here as if they came from an MCU
     * /anchor/to_vic/relay
         - Core, Arm, and Bio publish VicCAN messages to this topic to send to the MCU
     * /anchor/to_vic/relay_string
-        - Publish raw strings to this topic to send directly to the MCU for debugging
+        - Send raw strings to connectors. Does not work for connectors that require conversion (like CANConnector)
+    * /anchor/relay
+        - Legacy method for talking to connectors. Takes String as input, but does not send the raw strings to connectors.
+          Instead, it converts them to VicCAN messages first.
     """
 
+    connector: Connector
+
     def __init__(self):
-        # Initalize node with name
-        super().__init__("anchor_node")  # previously 'serial_publisher'
+        super().__init__("anchor_node")
 
-        self.serial_port: str | None = None  # e.g., "/dev/ttyUSB0"
+        logger = self.get_logger()
 
-        # Serial port override
-        if port_override := os.getenv("PORT_OVERRIDE"):
-            self.serial_port = port_override
+        # ROS2 Parameter Setup
 
-        ##################################################
-        # Serial MCU Discovery
+        self.declare_parameter(
+            "connector",
+            "auto",
+            ParameterDescriptor(
+                name="connector",
+                description="Declares which MCU connector should be used. Defaults to 'auto'.",
+                type=ParameterType.PARAMETER_STRING,
+                additional_constraints="Must be 'serial', 'can', 'mock', or 'auto'.",
+            ),
+        )
 
-        # If there was not a port override, look for a MCU over USB for Serial.
-        if self.serial_port is None:
-            comports = serial.tools.list_ports.comports()
-            real_ports = list(
-                filter(
-                    lambda p: p.vid is not None
-                    and p.pid is not None
-                    and p.device is not None,
-                    comports,
+        self.declare_parameter(
+            "can_override",
+            "",
+            ParameterDescriptor(
+                name="can_override",
+                description="Overrides which CAN channel will be used. Defaults to ''.",
+                type=ParameterType.PARAMETER_STRING,
+                additional_constraints="Must be a valid CAN network that shows up in `ip link show`.",
+            ),
+        )
+
+        self.declare_parameter(
+            "serial_override",
+            "",
+            ParameterDescriptor(
+                name="serial_override",
+                description="Overrides which serial port will be used. Defaults to ''.",
+                type=ParameterType.PARAMETER_STRING,
+                additional_constraints="Must be a valid path to a serial device file that shows up in `ls /dev/tty*`.",
+            ),
+        )
+
+        # Determine which connector to use. Options are Mock, Serial, and CAN
+        connector_select = (
+            self.get_parameter("connector").get_parameter_value().string_value
+        )
+        can_override = (
+            self.get_parameter("can_override").get_parameter_value().string_value
+        )
+        serial_override = (
+            self.get_parameter("serial_override").get_parameter_value().string_value
+        )
+        match connector_select:
+            case "serial":
+                logger.info("using serial connector")
+                self.connector = SerialConnector(
+                    logger, self.get_clock(), serial_override
                 )
-            )
-            recog_ports = list(filter(lambda p: (p.vid, p.pid) in KNOWN_USBS, comports))
-
-            if len(recog_ports) == 1:  # Found singular recognized MCU
-                found_port = recog_ports[0]
-                self.get_logger().info(
-                    f"Selecting MCU '{found_port.description}' at {found_port.device}."
+            case "can":
+                logger.info("using CAN connector")
+                self.connector = CANConnector(logger, self.get_clock(), can_override)
+            case "mock":
+                logger.info("using mock connector")
+                self.connector = MockConnector(logger, self.get_clock())
+            case "auto":
+                logger.info("automatically determining connector")
+                try:
+                    logger.info("trying CAN connector")
+                    self.connector = CANConnector(
+                        logger, self.get_clock(), can_override
+                    )
+                except (NoValidDeviceException, NoWorkingDeviceException, TypeError):
+                    logger.info("CAN connector failed, trying serial connector")
+                    self.connector = SerialConnector(
+                        logger, self.get_clock(), serial_override
+                    )
+            case _:
+                logger.fatal(
+                    f"invalid value for connector parameter: {connector_select}"
                 )
-                self.serial_port = found_port.device  # String, location of device file; e.g., '/dev/ttyACM0'
-            elif len(recog_ports) > 1:  # Found multiple recognized MCUs
-                # Kinda jank log message
-                self.get_logger().error(
-                    f"Found multiple recognized MCUs: {[p.device for p in recog_ports].__str__()}"
-                )
-                # Don't set self.serial_port; later if-statement will exit()
-            elif (
-                len(recog_ports) == 0 and len(real_ports) > 0
-            ):  # Found real ports but none recognized; i.e. maybe found an IMU or camera but not a MCU
-                self.get_logger().error(
-                    f"No recognized MCUs found; instead found {[p.device for p in real_ports].__str__()}."
-                )
-                # Don't set self.serial_port; later if-statement will exit()
-            else:  # Found jack shit
-                self.get_logger().error("No valid Serial ports specified or found.")
-                # Don't set self.serial_port; later if-statement will exit()
+                exit(1)
 
-        # We still don't have a serial port; fall back to legacy discovery (Areeb's code)
-        # Loop through all serial devices on the computer to check for the MCU
-        if self.serial_port is None:
-            self.get_logger().warning("Falling back to legacy MCU discovery...")
-            ports = Anchor.list_serial_ports()
-            for _ in range(4):
-                if self.serial_port is not None:
-                    break
-                for port in ports:
-                    try:
-                        # connect and send a ping command
-                        ser = serial.Serial(port, 115200, timeout=1)
-                        # (f"Checking port {port}...")
-                        ser.write(b"ping\n")
-                        response = ser.read_until(bytes("\n", "utf8"))
-
-                        # if pong is in response, then we are talking with the MCU
-                        if b"pong" in response:
-                            self.serial_port = port
-                            self.get_logger().info(f"Found MCU at {self.serial_port}!")
-                            break
-                    except:
-                        pass
-
-        # If port is still None then we ain't finding no mcu
-        if self.serial_port is None:
-            self.get_logger().error("Unable to find MCU. Exiting...")
-            time.sleep(1)
-            sys.exit(1)
-        # Found a Serial port, try to open it; above code has not officially opened a Serial port
-        else:
-            self.get_logger().debug(
-                f"Attempting to open Serial port '{self.serial_port}'..."
-            )
-            try:
-                self.serial_interface = serial.Serial(
-                    self.serial_port, 115200, timeout=1
-                )
-
-                # Attempt to get name of connected MCU
-                self.serial_interface.write(
-                    b"can_relay_mode,on\n"
-                )  # can_relay_ready,[mcu]
-                mcu_name: str = ""
-                for _ in range(4):
-                    response = self.serial_interface.read_until(bytes("\n", "utf8"))
-                    try:
-                        if b"can_relay_ready" in response:
-                            args: list[str] = response.decode("utf8").strip().split(",")
-                            if len(args) == 2:
-                                mcu_name = args[1]
-                            break
-                    except UnicodeDecodeError:
-                        pass  # ignore malformed responses
-                self.get_logger().info(
-                    f"MCU '{mcu_name}' is ready at '{self.serial_port}'."
-                )
-
-            except serial.SerialException as e:
-                self.get_logger().error(
-                    f"Could not open Serial port '{self.serial_port}' for reason:"
-                )
-                self.get_logger().error(e.strerror)
-                time.sleep(1)
-                sys.exit(1)
-
-        # Close serial port on exit
-        atexit.register(self.cleanup)
-
-        ##################################################
         # ROS2 Topic Setup
 
-        # New pub/sub with VicCAN
-        self.fromvic_debug_pub_ = self.create_publisher(
-            String, "/anchor/from_vic/debug", 20
+        # Publishers
+        self.fromvic_debug_pub_ = self.create_publisher(  # only used by serial
+            String,
+            "/anchor/from_vic/debug",
+            20,
         )
         self.fromvic_core_pub_ = self.create_publisher(
-            VicCAN, "/anchor/from_vic/core", 20
+            VicCAN,
+            "/anchor/from_vic/core",
+            20,
         )
         self.fromvic_arm_pub_ = self.create_publisher(
-            VicCAN, "/anchor/from_vic/arm", 20
+            VicCAN,
+            "/anchor/from_vic/arm",
+            20,
         )
         self.fromvic_bio_pub_ = self.create_publisher(
-            VicCAN, "/anchor/from_vic/bio", 20
+            VicCAN,
+            "/anchor/from_vic/bio",
+            20,
+        )
+        # Debug publisher
+        self.tovic_debug_pub_ = self.create_publisher(
+            String,
+            "/anchor/to_vic/debug",
+            20,
         )
 
-        self.mock_mcu_sub_ = self.create_subscription(
-            String, "/anchor/from_vic/mock_mcu", self.on_mock_fromvic, 20
-        )
+        # Subscribers
         self.tovic_sub_ = self.create_subscription(
-            VicCAN, "/anchor/to_vic/relay", self.on_relay_tovic_viccan, 20
+            VicCAN,
+            "/anchor/to_vic/relay",
+            self.write_connector,
+            20,
         )
-        self.tovic_debug_sub_ = self.create_subscription(
-            String, "/anchor/to_vic/relay_string", self.on_relay_tovic_string, 20
+        self.tovic_sub_legacy_ = self.create_subscription(
+            String,
+            "/anchor/relay",
+            self.write_connector_legacy,
+            20,
+        )
+        self.mock_mcu_sub_ = self.create_subscription(
+            VicCAN,
+            "/anchor/from_vic/mock_mcu",
+            self.relay_fromvic,
+            20,
+        )
+        self.tovic_string_sub_ = self.create_subscription(
+            String,
+            "/anchor/to_vic/relay_string",
+            self.write_connector_raw,
+            20,
         )
 
-        # Create publishers
-        self.arm_pub = self.create_publisher(String, "/anchor/arm/feedback", 10)
-        self.core_pub = self.create_publisher(String, "/anchor/core/feedback", 10)
-        self.bio_pub = self.create_publisher(String, "/anchor/bio/feedback", 10)
+        # poll at 100Hz for incoming data
+        self.read_timer_ = self.create_timer(0.01, self.read_connector)
 
-        self.debug_pub = self.create_publisher(String, "/anchor/debug", 10)
+    def destroy_node(self):
+        self.get_logger().info("closing connector")
+        self.connector.cleanup()
+        super().destroy_node()
 
-        # Create a subscriber
-        self.relay_sub = self.create_subscription(
-            String, "/anchor/relay", self.on_relay_tovic_string, 10
-        )
+    def read_connector(self):
+        """Check the connector for new data from the MCU, and publish string to appropriate topics"""
+        viccan, raw = self.connector.read()
 
-    def read_MCU(self):
-        """Check the USB serial port for new data from the MCU, and publish string to appropriate topics"""
-        try:
-            output = str(self.serial_interface.readline(), "utf8")
+        if raw:
+            self.fromvic_debug_pub_.publish(String(data=raw))
 
-            if output:
-                self.relay_fromvic(output)
-                # All output over debug temporarily
-                # self.get_logger().info(f"[MCU] {output}")
-                msg = String()
-                msg.data = output
-                self.debug_pub.publish(msg)
-                if output.startswith("can_relay_fromvic,core"):
-                    self.core_pub.publish(msg)
-                elif output.startswith("can_relay_fromvic,arm") or output.startswith(
-                    "can_relay_fromvic,digit"
-                ):  # digit for voltage readings
-                    self.arm_pub.publish(msg)
-                if output.startswith("can_relay_fromvic,citadel") or output.startswith(
-                    "can_relay_fromvic,digit"
-                ):  # digit for SHT sensor
-                    self.bio_pub.publish(msg)
-                # msg = String()
-                # msg.data = output
-                # self.debug_pub.publish(msg)
-                return
-        except serial.SerialException as e:
-            print(f"SerialException: {e}")
-            print("Closing serial port.")
-            try:
-                if self.serial_interface.is_open:
-                    self.serial_interface.close()
-            except:
-                pass
-            exit(1)
-        except TypeError as e:
-            print(f"TypeError: {e}")
-            print("Closing serial port.")
-            try:
-                if self.serial_interface.is_open:
-                    self.serial_interface.close()
-            except:
-                pass
-            exit(1)
-        except Exception as e:
-            print(f"Exception: {e}")
-            # print("Closing serial port.")
-            # if self.ser.is_open:
-            #     self.ser.close()
-            # exit(1)
+        if viccan:
+            self.relay_fromvic(viccan)
 
-    def on_mock_fromvic(self, msg: String):
-        """For testing without an actual MCU, publish strings here as if they came from an MCU"""
-        # self.get_logger().info(f"Got command from mock MCU: {msg}")
-        self.relay_fromvic(msg.data)
+    def write_connector(self, msg: VicCAN):
+        """Write to the connector and send a copy to /anchor/to_vic/debug"""
+        self.connector.write(msg)
+        self.tovic_debug_pub_.publish(String(data=viccan_to_string(msg)))
 
-    def on_relay_tovic_viccan(self, msg: VicCAN):
-        """Relay a VicCAN message to the MCU"""
-        output: str = f"can_relay_tovic,{msg.mcu_name},{msg.command_id}"
-        for num in msg.data:
-            output += f",{round(num, 7)}"  # limit to 7 decimal places
-        output += "\n"
-        # self.get_logger().info(f"VicCAN relay to MCU: {output}")
-        self.serial_interface.write(bytes(output, "utf8"))
+    def write_connector_raw(self, msg: String):
+        """Write raw string to the connector and send a copy to /anchor/to_vic/debug"""
+        self.connector.write_raw(msg)
+        self.tovic_debug_pub_.publish(msg)
 
-    def relay_fromvic(self, msg: str):
-        """Relay a string message from the MCU to the appropriate VicCAN topic"""
-        self.fromvic_debug_pub_.publish(String(data=msg))
-        parts = msg.strip().split(",")
-        if len(parts) > 0 and parts[0] != "can_relay_fromvic":
-            self.get_logger().debug(f"Ignoring non-VicCAN message: '{msg.strip()}'")
-            return
-
-        # String validation
-        malformed: bool = False
-        malformed_reason: str = ""
-        if len(parts) < 3 or len(parts) > 7:
-            malformed = True
-            malformed_reason = (
-                f"invalid argument count (expected [3,7], got {len(parts)})"
+    @deprecated(
+        "Use /anchor/to_vic/relay or /anchor/to_vic/relay_string instead of /anchor/relay"
+    )
+    def write_connector_legacy(self, msg: String):
+        """Write to the connector by first attempting to convert String to VicCAN"""
+        # please do not reference this code. ~riley
+        for cmd in msg.data.split("\n"):
+            viccan = string_to_viccan(
+                cmd,
+                "anchor",
+                self.get_logger(),
+                self.get_clock().now().to_msg(),
             )
-        elif parts[1] not in ["core", "arm", "digit", "citadel", "broadcast"]:
-            malformed = True
-            malformed_reason = f"invalid mcu_name '{parts[1]}'"
-        elif not (parts[2].isnumeric()) or int(parts[2]) < 0:
-            malformed = True
-            malformed_reason = f"command_id '{parts[2]}' is not a non-negative integer"
-        else:
-            for x in parts[3:]:
-                try:
-                    float(x)
-                except ValueError:
-                    malformed = True
-                    malformed_reason = f"data '{x}' is not a float"
-                    break
+            if viccan:
+                self.write_connector(viccan)
 
-        if malformed:
-            self.get_logger().warning(
-                f"Ignoring malformed from_vic message: '{msg.strip()}'; reason: {malformed_reason}"
-            )
-            return
-
-        # Have valid VicCAN message
-
-        output = VicCAN()
-        output.mcu_name = parts[1]
-        output.command_id = int(parts[2])
-        if len(parts) > 3:
-            output.data = [float(x) for x in parts[3:]]
-        output.header = Header(
-            stamp=self.get_clock().now().to_msg(), frame_id="from_vic"
-        )
-
-        # self.get_logger().info(f"Relaying from MCU: {output}")
-        if output.mcu_name == "core":
-            self.fromvic_core_pub_.publish(output)
-        elif output.mcu_name == "arm" or output.mcu_name == "digit":
-            self.fromvic_arm_pub_.publish(output)
-        elif output.mcu_name == "citadel" or output.mcu_name == "digit":
-            self.fromvic_bio_pub_.publish(output)
-
-    def on_relay_tovic_string(self, msg: String):
-        """Relay a raw string message to the MCU for debugging"""
-        message = msg.data
-        # self.get_logger().info(f"Sending command to MCU: {msg}")
-        self.serial_interface.write(bytes(message, "utf8"))
-
-    @staticmethod
-    def list_serial_ports():
-        return glob.glob("/dev/ttyUSB*") + glob.glob("/dev/ttyACM*")
-
-    def cleanup(self):
-        print("Cleaning up before terminating...")
-        if self.serial_interface.is_open:
-            self.serial_interface.close()
+    def relay_fromvic(self, msg: VicCAN):
+        """Relay a message from the MCU to the appropriate VicCAN topic"""
+        if msg.mcu_name == "core":
+            self.fromvic_core_pub_.publish(msg)
+        if msg.mcu_name == "arm" or msg.mcu_name == "digit":
+            self.fromvic_arm_pub_.publish(msg)
+        if msg.mcu_name == "citadel" or msg.mcu_name == "digit":
+            self.fromvic_bio_pub_.publish(msg)
 
 
 def main(args=None):
+    rclpy.init(args=args)
+    anchor_node = Anchor()
+    executor = SingleThreadedExecutor()
+    executor.add_node(anchor_node)
+
     try:
-        rclpy.init(args=args)
-        anchor_node = Anchor()
-
-        thread = threading.Thread(target=rclpy.spin, args=(anchor_node,), daemon=True)
-        thread.start()
-
-        rate = anchor_node.create_rate(100)  # 100 Hz -- arbitrary rate
-        while rclpy.ok():
-            anchor_node.read_MCU()  # Check the MCU for updates
-            rate.sleep()
+        executor.spin()
     except (KeyboardInterrupt, ExternalShutdownException):
-        print("Caught shutdown signal, shutting down...")
+        pass
     finally:
+        # don't accept any more jobs
+        executor.shutdown()
+        # make the node quit processing things
+        anchor_node.destroy_node()
+        # shut down everything else
         rclpy.try_shutdown()
-
-
-if __name__ == "__main__":
-    signal.signal(
-        signal.SIGTERM, lambda signum, frame: sys.exit(0)
-    )  # Catch termination signals and exit cleanly
-    main()

src/anchor_pkg/anchor_pkg/connector.py

@@ -0,0 +1,441 @@
+from abc import ABC, abstractmethod
+from astra_msgs.msg import VicCAN
+from std_msgs.msg import String
+from rclpy.clock import Clock
+from rclpy.impl.rcutils_logger import RcutilsLogger
+from .convert import string_to_viccan as _string_to_viccan, viccan_to_string
+
+# CAN
+import can
+import can.interfaces.socketcan
+import struct
+
+# Serial
+import serial
+import serial.tools.list_ports
+
+KNOWN_USBS = [
+    (0x2E8A, 0x00C0),  # Raspberry Pi Pico
+    (0x1A86, 0x55D4),  # Adafruit Feather ESP32 V2
+    (0x10C4, 0xEA60),  # DOIT ESP32 Devkit V1
+    (0x1A86, 0x55D3),  # ESP32 S3 Development Board
+]
+BAUD_RATE = 115200
+
+MCU_IDS = [
+    "broadcast",
+    "core",
+    "arm",
+    "digit",
+    "faerie",
+    "citadel",
+    "libs",
+]
+
+
+class NoValidDeviceException(Exception):
+    pass
+
+
+class NoWorkingDeviceException(Exception):
+    pass
+
+
+class MultipleValidDevicesException(Exception):
+    pass
+
+
+class DeviceClosedException(Exception):
+    pass
+
+
+class Connector(ABC):
+    logger: RcutilsLogger
+    clock: Clock
+
+    def string_to_viccan(self, msg: str, mcu_name: str):
+        """function currying so that we do not need to pass logger and clock every time"""
+        return _string_to_viccan(
+            msg,
+            mcu_name,
+            self.logger,
+            self.clock.now().to_msg(),
+        )
+
+    def __init__(self, logger: RcutilsLogger, clock: Clock):
+        self.logger = logger
+        self.clock = clock
+
+    @abstractmethod
+    def read(self) -> tuple[VicCAN | None, str | None]:
+        """
+        Must return a tuple of (VicCAN, debug message or string repr of VicCAN)
+        """
+        pass
+
+    @abstractmethod
+    def write(self, msg: VicCAN):
+        pass
+
+    @abstractmethod
+    def write_raw(self, msg: String):
+        pass
+
+    def cleanup(self):
+        pass
+
+
+class SerialConnector(Connector):
+    port: str
+    mcu_name: str
+    serial_interface: serial.Serial
+
+    def __init__(self, logger: RcutilsLogger, clock: Clock, serial_override: str = ""):
+        super().__init__(logger, clock)
+
+        ports = self._find_ports()
+        mcu_name: str | None = None
+
+        if serial_override:
+            logger.warn(
+                f"using serial_override: `{serial_override}`! this will bypass several checks."
+            )
+            ports = [serial_override]
+            mcu_name = "override"
+
+        if len(ports) <= 0:
+            raise NoValidDeviceException("no valid serial device found")
+        if (l := len(ports)) > 1:
+            raise MultipleValidDevicesException(
+                f"too many ({l}) valid serial devices found"
+            )
+
+        # check each of our ports to make sure one of them is responding
+        port = ports[0]
+        # we might already have a name by now if we overrode earlier
+        mcu_name = mcu_name or self._get_name(port)
+        if not mcu_name:
+            raise NoWorkingDeviceException(
+                f"found {port}, but it did not respond with its name"
+            )
+
+        self.port = port
+        self.mcu_name = mcu_name
+
+        # if we fail at this point, it should crash because we've already tested the port
+        self.serial_interface = serial.Serial(self.port, BAUD_RATE, timeout=1)
+
+    def _find_ports(self) -> list[str]:
+        """
+        Finds all valid ports but does not test them
+
+        returns: all valid ports
+        """
+        comports = serial.tools.list_ports.comports()
+        valid_ports = list(
+            map(  # get just device strings
+                lambda p: p.device,
+                filter(  # make sure we have a known device
+                    lambda p: (p.vid, p.pid) in KNOWN_USBS and p.device is not None,
+                    comports,
+                ),
+            )
+        )
+        self.logger.info(f"found valid MCU ports: [ {', '.join(valid_ports)} ]")
+        return valid_ports
+
+    def _get_name(self, port: str) -> str | None:
+        """
+        Get the name of the MCU (if it works)
+
+        returns: str name of the MCU, None if it doesn't work
+        """
+        # attempt to open the serial port
+        serial_interface: serial.Serial
+        try:
+            self.logger.info(f"asking {port} for its name")
+            serial_interface = serial.Serial(port, BAUD_RATE, timeout=1)
+
+            serial_interface.write(b"can_relay_mode,on\n")
+
+            for i in range(4):
+                self.logger.debug(f"attempt {i + 1} of 4 asking {port} for its name")
+                response = serial_interface.read_until(bytes("\n", "utf8"))
+                try:
+                    if b"can_relay_ready" in response:
+                        args: list[str] = response.decode("utf8").strip().split(",")
+                        if len(args) == 2:
+                            self.logger.info(f"we are talking to {args[1]}")
+                            return args[1]
+                        break
+                except UnicodeDecodeError as e:
+                    self.logger.info(
+                        f"ignoring UnicodeDecodeError when asking for MCU name: {e}"
+                    )
+
+            if serial_interface.is_open:
+                # turn relay mode off if it failed to respond with its name
+                serial_interface.write(b"can_relay_mode,off\n")
+                serial_interface.close()
+        except serial.SerialException as e:
+            self.logger.error(f"SerialException when asking for MCU name: {e}")
+
+        return None
+
+    def read(self) -> tuple[VicCAN | None, str | None]:
+        try:
+            raw = str(self.serial_interface.readline(), "utf8")
+
+            if not raw:
+                return (None, None)
+
+            return (
+                self.string_to_viccan(raw, self.mcu_name),
+                raw,
+            )
+        except serial.SerialException as e:
+            self.logger.error(f"SerialException: {e}")
+            raise DeviceClosedException(f"serial port {self.port} closed unexpectedly")
+        except Exception:
+            return (None, None)  # pretty much no other error matters
+
+    def write(self, msg: VicCAN):
+        self.write_raw(String(data=viccan_to_string(msg)))
+
+    def write_raw(self, msg: String):
+        self.serial_interface.write(bytes(msg.data, "utf8"))
+
+    def cleanup(self):
+        self.logger.info(f"closing serial port if open {self.port}")
+        try:
+            if self.serial_interface.is_open:
+                self.serial_interface.close()
+        except Exception as e:
+            self.logger.error(e)
+
+
+class CANConnector(Connector):
+    def __init__(self, logger: RcutilsLogger, clock: Clock, can_override: str):
+        super().__init__(logger, clock)
+
+        self.can_channel: str | None = None
+        self.can_bus: can.BusABC | None = None
+
+        avail = can.interfaces.socketcan.SocketcanBus._detect_available_configs()
+
+        if len(avail) == 0:
+            raise NoValidDeviceException("no CAN interfaces found")
+
+        # filter to busses whose channel matches the can_override
+        if can_override:
+            self.logger.info(f"overrode can interface with {can_override}")
+            avail = list(
+                filter(
+                    lambda b: b.get("channel") == can_override,
+                    avail,
+                )
+            )
+
+        if (l := len(avail)) > 1:
+            channels = ", ".join(str(b.get("channel")) for b in avail)
+            raise MultipleValidDevicesException(
+                f"too many ({l}) CAN interfaces found: [{channels}]"
+            )
+
+        bus = avail[0]
+        self.can_channel = str(bus.get("channel"))
+        self.logger.info(f"found CAN interface '{self.can_channel}'")
+
+        try:
+            self.can_bus = can.Bus(
+                interface="socketcan",
+                channel=self.can_channel,
+                bitrate=1_000_000,
+            )
+        except can.CanError as e:
+            raise NoWorkingDeviceException(
+                f"could not open CAN channel '{self.can_channel}': {e}"
+            )
+
+        if self.can_channel and self.can_channel.startswith("v"):
+            self.logger.warn("CAN interface is likely virtual")
+
+    def read(self) -> tuple[VicCAN | None, str | None]:
+        if not self.can_bus:
+            raise DeviceClosedException("CAN bus not initialized")
+
+        try:
+            message = self.can_bus.recv(timeout=0.0)
+        except can.CanError as e:
+            self.logger.error(f"CAN error while receiving: {e}")
+            raise DeviceClosedException("CAN bus closed unexpectedly")
+
+        if message is None:
+            return (None, None)
+
+        arbitration_id = message.arbitration_id & 0x7FF
+        data_bytes = bytes(message.data)
+
+        mcu_key = (arbitration_id >> 8) & 0b111
+        data_type_key = (arbitration_id >> 6) & 0b11
+        command = arbitration_id & 0x3F
+
+        try:
+            mcu_name = MCU_IDS[mcu_key]
+        except IndexError:
+            self.logger.warn(
+                f"received CAN frame with unknown MCU key {mcu_key}; id=0x{arbitration_id:X}"
+            )
+            return (None, None)
+
+        data: list[float] = []
+
+        try:
+            if data_type_key == 3:
+                data = []
+            elif data_type_key == 0:
+                if len(data_bytes) < 8:
+                    self.logger.warn(
+                        f"received double payload with insufficient length {len(data_bytes)}; dropping frame"
+                    )
+                    return (None, None)
+                (value,) = struct.unpack(">d", data_bytes[:8])
+                data = [float(value)]
+            elif data_type_key == 1:
+                if len(data_bytes) < 8:
+                    self.logger.warn(
+                        f"received float32x2 payload with insufficient length {len(data_bytes)}; dropping frame"
+                    )
+                    return (None, None)
+                v1, v2 = struct.unpack(">ff", data_bytes[:8])
+                data = [float(v1), float(v2)]
+            elif data_type_key == 2:
+                if len(data_bytes) < 8:
+                    self.logger.warn(
+                        f"received int16x4 payload with insufficient length {len(data_bytes)}; dropping frame"
+                    )
+                    return (None, None)
+                i1, i2, i3, i4 = struct.unpack(">hhhh", data_bytes[:8])
+                data = [float(i1), float(i2), float(i3), float(i4)]
+            else:
+                self.logger.warn(
+                    f"received CAN frame with unknown data_type_key {data_type_key}; id=0x{arbitration_id:X}"
+                )
+                return (None, None)
+        except struct.error as e:
+            self.logger.error(f"error unpacking CAN payload: {e}")
+            return (None, None)
+
+        viccan = VicCAN(
+            mcu_name=mcu_name,
+            command_id=int(command),
+            data=data,
+        )
+
+        self.logger.debug(
+            f"received CAN frame id=0x{message.arbitration_id:X}, "
+            f"decoded as VicCAN(mcu_name={viccan.mcu_name}, command_id={viccan.command_id}, data={viccan.data})"
+        )
+
+        return (
+            viccan,
+            f"{viccan.mcu_name},{viccan.command_id},"
+            + ",".join(map(str, list(viccan.data))),
+        )
+
+    def write(self, msg: VicCAN):
+        if not self.can_bus:
+            raise DeviceClosedException("CAN bus not initialized")
+
+        # build 11-bit arbitration ID according to VicCAN spec:
+        # bits 10..8: targeted MCU key
+        # bits 7..6:  data type key
+        # bits 5..0:  command
+
+        # map MCU name to 3-bit key.
+        try:
+            mcu_id = MCU_IDS.index((msg.mcu_name or "").lower())
+        except ValueError:
+            self.logger.error(
+                f"unknown VicCAN mcu_name '{msg.mcu_name}' for CAN frame; dropping message"
+            )
+            return
+
+        # determine data type from length:
+        # 0: double x1, 1: float32 x2, 2: int16 x4, 3: empty
+        match data_len := len(msg.data):
+            case 0:
+                data_type = 3
+                data = bytes()
+            case 1:
+                data_type = 0
+                data = struct.pack(">d", *msg.data)
+            case 2:
+                data_type = 1
+                data = struct.pack(">ff", *msg.data)
+            case 3 | 4:  # 3 gets treated as 4
+                data_type = 2
+                if data_len == 3:
+                    msg.data.append(0)
+                data = struct.pack(">hhhh", *[int(x) for x in msg.data])
+            case _:
+                self.logger.error(
+                    f"unexpected VicCAN data length: {data_len}; dropping message"
+                )
+                return
+
+        # command is limited to 6 bits.
+        command = int(msg.command_id)
+        if command < 0 or command > 0x3F:
+            self.logger.error(
+                f"invalid command_id for CAN frame: {command}; dropping message"
+            )
+            return
+
+        try:
+            can_message = can.Message(
+                arbitration_id=(mcu_id << 8) | (data_type << 6) | command,
+                data=data,
+                is_extended_id=False,
+            )
+        except Exception as e:
+            self.logger.error(f"failed to construct CAN message: {e}")
+            return
+
+        try:
+            self.can_bus.send(can_message)
+            self.logger.debug(
+                f"sent CAN frame id=0x{can_message.arbitration_id:X}, "
+                f"data={list(can_message.data)}"
+            )
+        except can.CanError as e:
+            self.logger.error(f"CAN error while sending: {e}")
+            raise DeviceClosedException("CAN bus closed unexpectedly")
+
+    def write_raw(self, msg: String):
+        self.logger.warn(
+            f"write_raw is not supported for CANConnector. msg: {msg.data}"
+        )
+
+    def cleanup(self):
+        try:
+            if self.can_bus is not None:
+                self.logger.info("shutting down CAN bus")
+                self.can_bus.shutdown()
+        except Exception as e:
+            self.logger.error(e)
+
+
+class MockConnector(Connector):
+    def __init__(self, logger: RcutilsLogger, clock: Clock):
+        super().__init__(logger, clock)
+        # No hardware interface for MockConnector. Publish to `/anchor/from_vic/mock_mcu` instead.
+
+    def read(self) -> tuple[VicCAN | None, str | None]:
+        return (None, None)
+
+    def write(self, msg: VicCAN):
+        pass
+
+    def write_raw(self, msg: String):
+        pass

src/anchor_pkg/anchor_pkg/convert.py

@@ -0,0 +1,65 @@
+from astra_msgs.msg import VicCAN
+from std_msgs.msg import Header
+from builtin_interfaces.msg import Time
+from rclpy.impl.rcutils_logger import RcutilsLogger
+
+
+def string_to_viccan(
+    msg: str, mcu_name: str, logger: RcutilsLogger, time: Time
+) -> VicCAN | None:
+    """
+    Converts the serial string VicCAN format to a ROS2 VicCAN message.
+    Does not fill out the Header of the message.
+    On a failure, it will log at a debug level why it failed and return None.
+    """
+
+    parts: list[str] = msg.strip().split(",")
+
+    # don't need an extra check because len of .split output is always >= 1
+    if not parts[0].startswith("can_relay_"):
+        logger.debug(f"got non-CAN data from {mcu_name}: {msg}")
+        return None
+    elif len(parts) < 3:
+        logger.debug(f"got garbage (not enough parts) CAN data from {mcu_name}: {msg}")
+        return None
+    elif len(parts) > 7:
+        logger.debug(f"got garbage (too many parts) CAN data from {mcu_name}: {msg}")
+        return None
+
+    try:
+        command_id = int(parts[2])
+    except ValueError:
+        logger.debug(
+            f"got garbage (non-integer command id) CAN data from {mcu_name}: {msg}"
+        )
+        return None
+
+    if command_id not in range(64):
+        logger.debug(
+            f"got garbage (wrong command id {command_id}) CAN data from {mcu_name}: {msg}"
+        )
+        return None
+
+    try:
+        return VicCAN(
+            header=Header(
+                stamp=time,
+                frame_id="from_vic",
+            ),
+            mcu_name=parts[1],
+            command_id=command_id,
+            data=[float(x) for x in parts[3:]],
+        )
+    except ValueError:
+        logger.debug(f"got garbage (non-numerical) CAN data from {mcu_name}: {msg}")
+        return None
+
+
+def viccan_to_string(viccan: VicCAN) -> str:
+    """Converts a ROS2 VicCAN message to the serial string VicCAN format."""
+    # make sure we accept 3 digits and treat it as 4
+    if len(viccan.data) == 3:
+        viccan.data.append(0)
+    # go from [ w, x, y, z ] -> ",w,x,y,z" & round to 7 digits max
+    data = "".join([f",{round(val,7)}" for val in viccan.data])
+    return f"can_relay_tovic,{viccan.mcu_name},{viccan.command_id}{data}\n"

src/anchor_pkg/launch/rover.launch.py

@@ -1,138 +1,111 @@
-#!/usr/bin/env python3
-
 from launch import LaunchDescription
-from launch.actions import DeclareLaunchArgument, OpaqueFunction, Shutdown
-from launch.substitutions import (
-    LaunchConfiguration,
-    ThisLaunchFileDir,
-    PathJoinSubstitution,
-)
-from launch_ros.actions import Node
+from launch.actions import DeclareLaunchArgument, Shutdown
 from launch.conditions import IfCondition
-
-
-# Prevent making __pycache__ directories
-from sys import dont_write_bytecode
-
-dont_write_bytecode = True
-
-
-def launch_setup(context, *args, **kwargs):
-    # Retrieve the resolved value of the launch argument 'mode'
-    mode = LaunchConfiguration("mode").perform(context)
-    nodes = []
-
-    if mode == "anchor":
-        # Launch every node and pass "anchor" as the parameter
-
-        nodes.append(
-            Node(
-                package="arm_pkg",
-                executable="arm",  # change as needed
-                name="arm",
-                output="both",
-                parameters=[{"launch_mode": mode}],
-                on_exit=Shutdown(),
-            )
-        )
-        nodes.append(
-            Node(
-                package="core_pkg",
-                executable="core",  # change as needed
-                name="core",
-                output="both",
-                parameters=[{"launch_mode": mode}],
-                on_exit=Shutdown(),
-            )
-        )
-        nodes.append(
-            Node(
-                package="core_pkg",
-                executable="ptz",  # change as needed
-                name="ptz",
-                output="both",
-                condition=IfCondition(LaunchConfiguration("use_ptz", default="true")),
-                # Currently don't shutdown all nodes if the PTZ node fails, as it is not critical
-                # on_exit=Shutdown()  # Uncomment if you want to shutdown on PTZ failure
-            )
-        )
-        nodes.append(
-            Node(
-                package="bio_pkg",
-                executable="bio",  # change as needed
-                name="bio",
-                output="both",
-                parameters=[{"launch_mode": mode}],
-                on_exit=Shutdown(),
-            )
-        )
-        nodes.append(
-            Node(
-                package="anchor_pkg",
-                executable="anchor",  # change as needed
-                name="anchor",
-                output="both",
-                parameters=[{"launch_mode": mode}],
-                on_exit=Shutdown(),
-            )
-        )
-    elif mode in ["arm", "core", "bio", "ptz"]:
-        # Only launch the node corresponding to the provided mode.
-        if mode == "arm":
-            nodes.append(
-                Node(
-                    package="arm_pkg",
-                    executable="arm",
-                    name="arm",
-                    output="both",
-                    parameters=[{"launch_mode": mode}],
-                    on_exit=Shutdown(),
-                )
-            )
-        elif mode == "core":
-            nodes.append(
-                Node(
-                    package="core_pkg",
-                    executable="core",
-                    name="core",
-                    output="both",
-                    parameters=[{"launch_mode": mode}],
-                    on_exit=Shutdown(),
-                )
-            )
-        elif mode == "bio":
-            nodes.append(
-                Node(
-                    package="bio_pkg",
-                    executable="bio",
-                    name="bio",
-                    output="both",
-                    parameters=[{"launch_mode": mode}],
-                    on_exit=Shutdown(),
-                )
-            )
-        elif mode == "ptz":
-            nodes.append(
-                Node(
-                    package="core_pkg",
-                    executable="ptz",
-                    name="ptz",
-                    output="both",
-                    on_exit=Shutdown(),  # on fail, shutdown if this was the only node to be launched
-                )
-            )
-    else:
-        # If an invalid mode is provided, print an error.
-        print("Invalid mode provided. Choose one of: arm, core, bio, anchor, ptz.")
-
-    return nodes
+from launch.substitutions import LaunchConfiguration
+from launch_ros.actions import Node
 
 
 def generate_launch_description():
-    declare_arg = DeclareLaunchArgument(
-        "mode",
-        default_value="anchor",
-        description="Launch mode: arm, core, bio, anchor, or ptz",
+    connector = LaunchConfiguration("connector")
+    serial_override = LaunchConfiguration("serial_override")
+    can_override = LaunchConfiguration("can_override")
+    use_ptz = LaunchConfiguration("use_ptz")
+
+    ld = LaunchDescription()
+
+    # arguments
+    ld.add_action(
+        DeclareLaunchArgument(
+            "connector",
+            default_value="auto",
+            description="Connector parameter for anchor node (default: 'auto')",
+        )
     )
 
-    return LaunchDescription([declare_arg, OpaqueFunction(function=launch_setup)])
+    ld.add_action(
+        DeclareLaunchArgument(
+            "serial_override",
+            default_value="",
+            description="Serial port override parameter for anchor node (default: '')",
+        )
+    )
+
+    ld.add_action(
+        DeclareLaunchArgument(
+            "can_override",
+            default_value="",
+            description="CAN network override parameter for anchor node (default: '')",
+        )
+    )
+
+    ld.add_action(
+        DeclareLaunchArgument(
+            "use_ptz",
+            default_value="true",  # must be string for launch system
+            description="Whether to launch PTZ node (default: true)",
+        )
+    )
+
+    # nodes
+    ld.add_action(
+        Node(
+            package="arm_pkg",
+            executable="arm",
+            name="arm",
+            output="both",
+            parameters=[{"launch_mode": "anchor"}],
+            on_exit=Shutdown(),
+        )
+    )
+
+    ld.add_action(
+        Node(
+            package="core_pkg",
+            executable="core",
+            name="core",
+            output="both",
+            parameters=[{"launch_mode": "anchor"}],
+            on_exit=Shutdown(),
+        )
+    )
+
+    ld.add_action(
+        Node(
+            package="core_pkg",
+            executable="ptz",
+            name="ptz",
+            output="both",
+            condition=IfCondition(use_ptz),
+        )
+    )
+
+    ld.add_action(
+        Node(
+            package="bio_pkg",
+            executable="bio",
+            name="bio",
+            output="both",
+            parameters=[{"launch_mode": "anchor"}],
+            on_exit=Shutdown(),
+        )
+    )
+
+    ld.add_action(
+        Node(
+            package="anchor_pkg",
+            executable="anchor",
+            name="anchor",
+            output="both",
+            parameters=[
+                {
+                    "launch_mode": "anchor",
+                    "connector": connector,
+                    "serial_override": serial_override,
+                    "can_override": can_override,
+                }
+            ],
+            on_exit=Shutdown(),
+        )
+    )
+
+    return ld

src/anchor_pkg/package.xml

@@ -3,13 +3,14 @@
 <package format="3">
   <name>anchor_pkg</name>
   <version>0.0.0</version>
-  <description>TODO: Package description</description>
-  <maintainer email="tristanmcginnis26@gmail.com">tristan</maintainer>
+  <description>Anchor -- ROS and CAN relay node</description>
+  <maintainer email="rjm0037@uah.edu">Riley</maintainer>
   <license>AGPL-3.0-only</license>
 
   <depend>rclpy</depend>
   <depend>common_interfaces</depend>
   <depend>python3-serial</depend>
+  <depend>python3-can</depend>
 
   <build_depend>black</build_depend>
 

src/core_pkg/core_pkg/core_ptz.py

@@ -262,7 +262,7 @@ class PtzNode(Node):
             f"[{self.get_clock().now().nanoseconds / 1e9:.2f}] PTZ Node: {message_text}"
         )
         self.debug_pub.publish(msg)
-        self.get_logger().info(message_text)
+        self.get_logger().debug(message_text)
 
     def run_async_func(self, coro):
         """Run an async function in the event loop."""

treefmt.nix

@@ -0,0 +1,9 @@
+{ ... }:
+{
+  projectRootFile = "flake.nix";
+  programs = {
+    nixfmt.enable = true;
+    black.enable = true;
+    shfmt.enable = true;
+  };
+}